My VentureShield installation
01-08-07 | 08:23 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
My VentureShield installation
Going to post several pictures which show the before, during, and after results. Went with Ventureshield instead of 3M. Got it done at X-Pert Tint in Houston, Tx.
Attached Thumbnails
01-08-07 | 08:24 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
Another before pic (for comparison)
another angle
Attached Thumbnails
01-08-07 | 08:25 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
one last before pic
another angle
Attached Thumbnails
01-08-07 | 08:27 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
1st Step - Claybar
The gentleman is Sunny, the owner of X-Pert Tint. Does lots of work on exotics and other high end cars. An LS460 came in while I was there today!
Attached Thumbnails
01-08-07 | 08:29 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
Putting on the clear bra on the bumper
Getting the Ventureshield onto the bumper - 2 person task!
Attached Thumbnails
01-08-07 | 08:31 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
Now for the fun part...
Sunny has to align everything perfectly...
Attached Thumbnails
01-08-07 | 08:33 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
Lot's of adjusting
...and more
Attached Thumbnails
01-08-07 | 08:35 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
and then press it into place
using what looks like a small hand held squeegee...
Attached Thumbnails
01-08-07 | 08:36 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
starting to look better already!
you can see the middle part is almost done and has become almost invisible already!
Attached Thumbnails
01-08-07 | 08:39 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
Fast forward 30 minutes or so...
And here's what it looks like after the Ventureshield has been applied!
Attached Thumbnails
01-08-07 | 08:41 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
After Pic: closer view of the hood
close up of the hood - can't really tell from this angle, lighting, and distance!
Attached Thumbnails
01-08-07 | 08:43 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
After Pic: front view
view from the front - again, can't see the clear bra.
Attached Thumbnails
01-08-07 | 08:45 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
After Pic: A closer view
Another indoor shot from a different angle, still can't really see the installation!
Attached Thumbnails
01-08-07 | 08:47 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
After Pic: In the sun
Lots of glare (glad I waxed the car
), but no evidence of the Ventureshield from this angle!
Attached Thumbnails
01-08-07 | 08:49 PM
Thread Starter
Joined: Nov 2006
Posts: 601
Likes: 21
From: Houston, TX
After Pic: Another outdoor front closeup
Another frontal shot and from this angle it is really tough to see where the Ventureshield is installed
Attached Thumbnails