My Aristo Single Turbo Project
05-18-13, 12:56 PM
Driver
Thread Starter
Join Date: Jan 2012
Location: New Zealand
Posts: 156
Likes: 0
Quote:
Originally Posted by
sakataj
they look like Figs spherical ones Tony....
Yup, FIGS sphericals.
05-23-13, 11:12 PM
Driver
Thread Starter
Join Date: Jan 2012
Location: New Zealand
Posts: 156
Likes: 0
Tuning complete (apart from a slightly screwy off idle stutter which Soichi is looking into)
384kw (515hp) @ wheels (401kw (538hp) using SAE correction) at 1.4bar, full boost at under 3500rpm
Excuse the quality - the good camera's SD card was full and didnt have time to delete stuff!
Dyno plots:
The red line is at 1.2bar, the green line is at 1.4bar - ignore the later curve and crazy loop on the green line - they had to back off at torque peak as it kept overloading the dyno and throwing up a big red shutdown message - was run in 2nd gear.
05-24-13, 02:04 PM
Driver
Thread Starter
Join Date: Jan 2012
Location: New Zealand
Posts: 156
Likes: 0
Doing some rough calcs and estimating auto trans loss at 17% that equates to 840Nm (620 ft lb) of torque at 3300rpm and 450kW (603bhp) at 6450RPM
05-25-13, 09:29 AM
Lexus Test Driver
Join Date: Jan 2009
Location: NY
Posts: 1,578
Likes: 0
Received 0 Likes
on
0 Posts
Nice numbers man
.
06-07-13, 05:59 PM
Driver
Thread Starter
Join Date: Jan 2012
Location: New Zealand
Posts: 156
Likes: 0
Moar Powah!
421 kw @ wheels (565whp) at 1.5bar of boost (once again had to back off in mid-range due to over-torquing the dyno)
Aaaand finished product:
06-07-13, 06:49 PM
5% Club. Killing it!!!
Join Date: Nov 2004
Location: FL
Posts: 21,942
looks really killer.. Have a link to the radiator u used... That looks pretty beefy...
06-07-13, 08:55 PM
Driver
Thread Starter
Join Date: Jan 2012
Location: New Zealand
Posts: 156
Likes: 0
06-08-13, 10:35 AM
Lead Lap
Join Date: Aug 2007
Location: fl
Posts: 699
Likes: 0
where did you get the top radiator brackets from?
06-08-13, 12:52 PM
Driver
Thread Starter
Join Date: Jan 2012
Location: New Zealand
Posts: 156
Likes: 0
06-08-13, 09:37 PM
Lead Lap
Join Date: Aug 2007
Location: fl
Posts: 699
Likes: 0
06-24-13, 07:53 PM
Pole Position
Join Date: Feb 2007
Location: Tx
Posts: 2,265
Likes: 0
Received 0 Likes
on
0 Posts
have you been having fun in the car? like beating the hell out of that tranny?
06-25-13, 03:10 AM
Driver
Thread Starter
Join Date: Jan 2012
Location: New Zealand
Posts: 156
Likes: 0
Trans is fine, lol, few teething issues with engine sensors but running really well, and enjoying the car.
07-05-13, 03:12 AM
Driver
Thread Starter
Join Date: Jan 2012
Location: New Zealand
Posts: 156
Likes: 0
Small update -
Finally got my VSC fixed, after throwing parts at it for awhile, turned out all it needed was a zero point calibration for the yaw sensor and steering angle that the dealer did for free, yay!
Also, this arrived
07-26-13, 05:12 PM
Pole Position
Join Date: Feb 2007
Location: Tx
Posts: 2,265
Likes: 0
Received 0 Likes
on
0 Posts
Has the tranny blew yet lol? I went ahead and got
Me a Titan stage 2 to mate up to my motor!
07-27-13, 05:08 AM
Lexus Test Driver
Join Date: May 2007
Location: Da hill fl
Posts: 1,307
Likes: 0
Received 0 Likes
on
0 Posts
Quote:
Originally Posted by
handoverfi
Has the tranny blew yet lol? I went ahead and got
Me a Titan stage 2 to mate up to my motor!
His tranny is slipping and he made another thread asking if he should build auto or go 5 sod.