SC300 1jz+r154 swap
02-07-20, 10:18 AM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
Now its painted and installed, looks ok to me, even it has some sights about "modification" but good enough for me.
Attached Thumbnails
The following 2 users liked this post by kakezzi22:
02-07-20, 10:44 AM
Pole Position
Join Date: Feb 2012
Location: CO
Posts: 2,384
It came out spectacular, nice work!
02-07-20, 01:29 PM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
Quote:
Originally Posted by RudysSC
It came out spectacular, nice work!
Thank you sir!
02-07-20, 11:45 PM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
Quote:
Originally Posted by mrmj2u
Looks really good!
Thank you, only i should have grown the lower part almost half inch more to make it "perfect" :-D But its finished and its good enough!
02-08-20, 02:19 AM
Moderator
Join Date: Jun 2010
Location: FL & CA
Posts: 7,227
Excellent result! Nice work!!
03-01-20, 05:04 AM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
I go with VAG cop ignition and denso spark plugs. Also bought new oem crank pulley(damper), read a lot that 30years old damper could "fly away" :-D
03-02-20, 06:26 AM
Pole Position
Join Date: Feb 2012
Location: CO
Posts: 2,384
^ Nice upgrades! My crank pulley fell apart on my GE and I ended up replacing it with a lightweight aluminum one. However, on my GTE, I kept the stock one knowing that I'll need to replace it at some point in time. I get worried about the horror stories of running a lightweight crank pulley, and on such a nice motor I didn't want to take the risk.
03-02-20, 11:05 AM
Moderator
Join Date: Jun 2010
Location: FL & CA
Posts: 7,227
I went with a new OEM crank pulley on mine. The only other pulley I’ve heard of people using reliably is the one by Fluidampr which uses, I think, some specific weight of internal gel or silicone inside it vs the OEM pulley’s rubber center.
04-11-20, 12:58 AM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
Teflon stainless fuel lines from TORQUE UK. I will make some metal protect plate for the lines.
Attached Thumbnails
The following users liked this post:
04-17-20, 09:20 AM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
3" downpipe "titanium" tape and aem wideband
Attached Thumbnails
Last edited by kakezzi22; 04-17-20 at 11:15 PM .
The following users liked this post:
04-27-20, 11:10 PM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
This week i have been doing my exhaust, 3 inch with 200 cell catalysator.
Attached Thumbnails
The following 2 users liked this post by kakezzi22:
04-29-20, 06:41 AM
Pole Position
Join Date: Feb 2012
Location: CO
Posts: 2,384
You're going to be brapping in no time!
04-30-20, 05:19 AM
Moderator
Join Date: Jun 2010
Location: FL & CA
Posts: 7,227
Quote:
Originally Posted by
RudysSC
You're going to be brapping in no time!
Definitely will be!
04-30-20, 12:20 PM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
Yea, have found some extra time for the build. Found some aluminium heat covers.
Attached Thumbnails
The following users liked this post:
05-18-20, 10:41 AM
Driver
Thread Starter
Join Date: Jul 2016
Location: Kangasala
Posts: 72
Still working on exhaust. About 3 or 4 small pieces to make and its finish
I have now 6 weeks holidays, trying to get it running before July.
Attached Thumbnails