IS300 on Nardos Sneak Peak
#1
Driver
Thread Starter
Join Date: Mar 2009
Location: BC
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
IS300 on Nardos Sneak Peak
Finally posted some pics up. Let me know what ya guys think.
Stock
Slammed on Teins, fully down on the front, 7 threads left on the rear
Nardos
Camber... needs fixing
Better pics coming soon.
Stock
Slammed on Teins, fully down on the front, 7 threads left on the rear
Nardos
Camber... needs fixing
Better pics coming soon.
#3
Lexus Fanatic
Join Date: Aug 2006
Location: Vancouver, BC
Posts: 7,468
Likes: 0
Received 0 Likes
on
0 Posts
Looks good man but dude, where are you going to drive? I rarely cross bridges and I think the roads are far less than stellar ...
Def looking forward to seeing you at a meet though
Def looking forward to seeing you at a meet though
#5
Driver
Thread Starter
Join Date: Mar 2009
Location: BC
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
#7
Driver
Thread Starter
Join Date: Mar 2009
Location: BC
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
thanks! ill def send him a msg.
on another note. i need to raise my rear. managed to high centre myself yesterday at washworld in langley. never come through the alley way.
managed to get out with just a few scrapes.
not as bad as this lady
on another note. i need to raise my rear. managed to high centre myself yesterday at washworld in langley. never come through the alley way.
managed to get out with just a few scrapes.
not as bad as this lady
Trending Topics
#11
Driver
Thread Starter
Join Date: Mar 2009
Location: BC
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
hahah im not sure where that is actually. just found it to be really funny.
thanks for the advice, ill pm and see what he says.
Uber-
as far as the cut outs, i did them myself. took the bumper off, used a dremel to cut out the whole and sanded it down...its hard to get to be exactly like the stock right side one but i got it close.
i went to whistler over the weekend, bottomed out on the highway, and hit the right exhaust causing it to point up more, with heat and driving, i smelled burnt plastic, turns out it was touching the bumper the whole time, so it melted a bit off around the edge... FML...
ill be getting an alignment this weekend so ill raise the **** up more. speed bumps and i arent friends anymore.
thanks for the advice, ill pm and see what he says.
Uber-
as far as the cut outs, i did them myself. took the bumper off, used a dremel to cut out the whole and sanded it down...its hard to get to be exactly like the stock right side one but i got it close.
i went to whistler over the weekend, bottomed out on the highway, and hit the right exhaust causing it to point up more, with heat and driving, i smelled burnt plastic, turns out it was touching the bumper the whole time, so it melted a bit off around the edge... FML...
ill be getting an alignment this weekend so ill raise the **** up more. speed bumps and i arent friends anymore.
#13
Driver
Thread Starter
Join Date: Mar 2009
Location: BC
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
right from the catback to resonator its a straight pipe, then the resonator, another straight with a Y where it splits just before the rear axle, and straight pipes out. no mufflers, just the resonator to keep the noise to a min. sounds mint, i love it.
#15
Driver
Thread Starter
Join Date: Mar 2009
Location: BC
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts