Now Available! GM LSx Engine Mounts for Lexus GS / IS300 / SC300 / SC400 - IN STOCK!
#17
Former Sponsor
Thread Starter
iTrader: (5)
Join Date: Aug 2011
Location: CA
Posts: 312
Likes: 0
Received 0 Likes
on
0 Posts
This is the best of the best stuff right here... Made in the USA!
The engine mount isolators:
What sets Ultra Mounts urethane mounts apart from our competition is our engine mounts have a two-part interlocking steel framework encased in urethane to give engine support in both directions of twist. When the engine tries to twist under acceleration the drivers side of the engine tries to lift, putting that mount in tension (pull apart) and the passenger side mount in compression (push together). Then when you gear down into a corner or to stop, these forces are reversed. Ultra Mounts are correctly designed and take both of these forces into account.
The engine mount isolators:
What sets Ultra Mounts urethane mounts apart from our competition is our engine mounts have a two-part interlocking steel framework encased in urethane to give engine support in both directions of twist. When the engine tries to twist under acceleration the drivers side of the engine tries to lift, putting that mount in tension (pull apart) and the passenger side mount in compression (push together). Then when you gear down into a corner or to stop, these forces are reversed. Ultra Mounts are correctly designed and take both of these forces into account.
Last edited by AMSMIKE2; 10-17-11 at 07:42 PM.
#18
Lexus Fanatic
iTrader: (182)
yup....JUST like this
got it...color essentially is kawasaki lime green
GUYS keep in mind this is a great price for some mounts. last time they sold it was for ALOT more than this not to mention only person in town making them correctly. i have dealt with mike many times, good dude....and i was talking to dan about getting a set before he stopped making them. i know these are made properly and alot cheaper than the 1400 or so DGR wanted. easy swap for the GS,IS, and SC community
GUYS keep in mind this is a great price for some mounts. last time they sold it was for ALOT more than this not to mention only person in town making them correctly. i have dealt with mike many times, good dude....and i was talking to dan about getting a set before he stopped making them. i know these are made properly and alot cheaper than the 1400 or so DGR wanted. easy swap for the GS,IS, and SC community
Last edited by sakataj; 09-15-11 at 05:18 PM.
#25
BahHumBug
iTrader: (10)
just a heads up, the 89+ supra (later 89) that use the newer round monts have the right subframe to use mounts out of an SC300. mounts should interchange but there will likely be t56 clearance issues in the tunnel. afaik.
LSx i can afford, but with the T56 it all becomes too rich for my blood at this point
LSx i can afford, but with the T56 it all becomes too rich for my blood at this point
#26
Former Sponsor
Thread Starter
iTrader: (5)
Join Date: Aug 2011
Location: CA
Posts: 312
Likes: 0
Received 0 Likes
on
0 Posts
just a heads up, the 89+ supra (later 89) that use the newer round monts have the right subframe to use mounts out of an SC300. mounts should interchange but there will likely be t56 clearance issues in the tunnel. afaik.
LSx i can afford, but with the T56 it all becomes too rich for my blood at this point
LSx i can afford, but with the T56 it all becomes too rich for my blood at this point
start saving
#29
Former Sponsor
Thread Starter
iTrader: (5)
Join Date: Aug 2011
Location: CA
Posts: 312
Likes: 0
Received 0 Likes
on
0 Posts
UPDATE!
IF I don't get 5-10 people. This group buy will be cancelled. The parts cost a lot to produce because everything is being made here locally by a machine shop that does quality work. I have been to over 10 machine shops trying to get the lowest price here. that's the ONLY way to get the price where its at right now is if 5-10 people are interested.
IF I don't get 5-10 people. This group buy will be cancelled. The parts cost a lot to produce because everything is being made here locally by a machine shop that does quality work. I have been to over 10 machine shops trying to get the lowest price here. that's the ONLY way to get the price where its at right now is if 5-10 people are interested.