eyelids
#1
eyelids
ok, i was thinking about getting those for my gs300, but no one seems to have them on their cars, is there a reason for it, i mean i haven't even seen 1.
Another question is about clear sidemarkers,i just got mines and I was wondering how to install them on the car, do i have to jack the car up and do if from the bottom? whats the best way to change them?
thank you
Eric
Another question is about clear sidemarkers,i just got mines and I was wondering how to install them on the car, do i have to jack the car up and do if from the bottom? whats the best way to change them?
thank you
Eric
#4
Originally posted by LXOGOOD
Here's your #1...
Steve Ganz (SUPRATRD) will be making eyelids for his own CarsonTuned line of products. This is a prototype. I believe Junction Produce carries eyelids too.
Here's your #1...
Steve Ganz (SUPRATRD) will be making eyelids for his own CarsonTuned line of products. This is a prototype. I believe Junction Produce carries eyelids too.
#6
Originally posted by rodel
When are the eyelids being released for sale?
When are the eyelids being released for sale?
Trending Topics
#8
Originally posted by LXOGOOD
Not sure since there hasn't been enough "I wants" for this type of mod. I would send Steve a PM and ask him about the eye lids we did for my car.
Not sure since there hasn't been enough "I wants" for this type of mod. I would send Steve a PM and ask him about the eye lids we did for my car.
#9
Here's what it looked like. Its probably f/g but it feels like a hard plastic. I bet I could use some dental floss or fishing line under there to remove the 3m tape without braking it...
Last edited by LXOGOOD; 07-23-04 at 12:22 AM.
#10
Originally posted by LXOGOOD
Here's what it looked like. Its probably f/g but it feels like a hard plastic. I bet I could use some dental floss or fishing line under there to remove the 3m tape without braking it...
Here's what it looked like. Its probably f/g but it feels like a hard plastic. I bet I could use some dental floss or fishing line under there to remove the 3m tape without braking it...
#11
i just got a pair of quest power eyelids though steve / carson toyota...
they're just for the inner two lights. (high beams)
Will post pictures later...just got back from a 500 mile roadtrip. Cars a little dirty.
they're just for the inner two lights. (high beams)
Will post pictures later...just got back from a 500 mile roadtrip. Cars a little dirty.
#12
Originally posted by PHML
Dee's got some....
Dee's got some....
I like this one, cause it has eyelids for all the front lights, where can i get those? thanks a lot?
Do you guys glue these or snap them in?
Thanks for the fast replies, I appreciate it.
#13
I believe they use 3m tape to put on. If that's the case and you change your mind about them. Good luck peeling them out without ruining your lense.
But I think eyelids are pretty sexy... now if our headlights were wider it'll look better.
But I think eyelids are pretty sexy... now if our headlights were wider it'll look better.
#14
Originally posted by LEXITT
I like this one, cause it has eyelids for all the front lights, where can i get those? thanks a lot?
Do you guys glue these or snap them in?
Thanks for the fast replies, I appreciate it.
I like this one, cause it has eyelids for all the front lights, where can i get those? thanks a lot?
Do you guys glue these or snap them in?
Thanks for the fast replies, I appreciate it.
#15
Originally posted by LXOGOOD
Not sure since there hasn't been enough "I wants" for this type of mod. I would send Steve a PM and ask him about the eye lids we did for my car.
Not sure since there hasn't been enough "I wants" for this type of mod. I would send Steve a PM and ask him about the eye lids we did for my car.