What did you do to your GS today?
#2852
Obviously you know not to even attempt to use that sprocket ^^^ lol
#2853
Driver School Candidate
#2854
Driver School Candidate
I cleaned my servo motor and wedged some aluminum foil in it so it would switch modes properly. I'm ordering a new servo motor, but the aluminum foil has done the trick so far.
The following 2 users liked this post by AnneDye:
Agent$mith (07-23-20),
firelizard (07-20-20)
#2855
5% Club. Killing it!!!
iTrader: (15)
Finally after 15yrs i had my TTE lip re-molded about a month ago. Over time it developed a crack on the mold and i just left it. Believe or not i had someone do this in my driveway. Turned out pretty good.
Installed the K&N intake system a few days ago after my factory air box developed a crack in the rear resonator area. Also re polished some pieces that needed a refresh.
Had my mirrors done in black the same time as my front bumper. Really like the black mirrors and contrast with the vehicle.
Next up are 18/19 wheels , LRD lower engine cover, oil catch can, tranny cooler, and Timing belt service.
👍👍
The following 3 users liked this post by tmf2004:
#2856
Instructor
iTrader: (24)
Installed my Clazzio seat cover kit. I ordered light brown color and was surprised it closely matches the saddle interior.
Fit and finish is on point. Have to make some final adjustments to the rear seats. I ordered extra materials to do the door inserts the same color. I will post more/better pics when I get everything
adjusted to my liking.
.
Fit and finish is on point. Have to make some final adjustments to the rear seats. I ordered extra materials to do the door inserts the same color. I will post more/better pics when I get everything
adjusted to my liking.
.
The following 5 users liked this post by BiGEZ:
8M6 (07-25-20),
Agent$mith (07-25-20),
SaiyanGS3 (07-25-20),
tmf2004 (07-25-20),
TrueGS300 (07-25-20)
#2857
Racer
iTrader: (8)
Installed my Clazzio seat cover kit. I ordered light brown color and was surprised it closely matches the saddle interior.
Fit and finish is on point. Have to make some final adjustments to the rear seats. I ordered extra materials to do the door inserts the same color. I will post more/better pics when I get everything
adjusted to my liking.
.
Fit and finish is on point. Have to make some final adjustments to the rear seats. I ordered extra materials to do the door inserts the same color. I will post more/better pics when I get everything
adjusted to my liking.
.
#2858
Instructor
iTrader: (24)
The wheels are ACE AFF02 19x8.5 35mm, 19x10 +40mm Chromium Black. BC coil over setup. A closer look at the wheel finish.
As for the seats, they are perforated leather inserts with vinyl outer. The kit is new, ordered this past May with a 6 weeks wait time. Paid $750 for the entire kit shipped. Yes the rear center arm rest need some work to fit the cup holder slot a bit better. I will work on getting it to fit better.
I did the install by myself in 95 degree weather, it was brutal. An extra set of hands would have been nice. I will complete the door inserts at a later date to give it a finished look.
As for the seats, they are perforated leather inserts with vinyl outer. The kit is new, ordered this past May with a 6 weeks wait time. Paid $750 for the entire kit shipped. Yes the rear center arm rest need some work to fit the cup holder slot a bit better. I will work on getting it to fit better.
I did the install by myself in 95 degree weather, it was brutal. An extra set of hands would have been nice. I will complete the door inserts at a later date to give it a finished look.
The following users liked this post:
tmf2004 (07-27-20)
The following 2 users liked this post by BiGEZ:
8M6 (08-23-20),
firelizard (07-27-20)
#2860
Driver School Candidate
#2861
Racer
iTrader: (8)
The wheels are ACE AFF02 19x8.5 35mm, 19x10 +40mm Chromium Black. BC coil over setup. A closer look at the wheel finish.
As for the seats, they are perforated leather inserts with vinyl outer. The kit is new, ordered this past May with a 6 weeks wait time. Paid $750 for the entire kit shipped. Yes the rear center arm rest need some work to fit the cup holder slot a bit better. I will work on getting it to fit better.
I did the install by myself in 95 degree weather, it was brutal. An extra set of hands would have been nice. I will complete the door inserts at a later date to give it a finished look.
As for the seats, they are perforated leather inserts with vinyl outer. The kit is new, ordered this past May with a 6 weeks wait time. Paid $750 for the entire kit shipped. Yes the rear center arm rest need some work to fit the cup holder slot a bit better. I will work on getting it to fit better.
I did the install by myself in 95 degree weather, it was brutal. An extra set of hands would have been nice. I will complete the door inserts at a later date to give it a finished look.
#2862
Driver School Candidate
picked up this sweet Imperial Jade gem 400 miles away and gave it some love! She had been neglected for a bit- but with a little elbow grease she came back to life!