Tesla Style Headunit with OEM Camera
#61
Driver
Thread Starter
The second hole located in the curved area. I will make it straight by a hammer. I am thinking of taking the measurements from the center of the new coles to the center of the nearby holes for you to be able to make it.
What do you think?
#62
Driver
Thread Starter
#63
Driver
Thread Starter
I noticed something with the new unit. Regardless how secured I made it with the brackets, the unit is flimsy and made of plastic and thin metal. So it moves when you press the corners of the unit.
#64
Driver School Candidate
Mine's the same at the top-left. There's a gap inside the unit there. I opened it up and put a wedge in to stop it pressing in.
#65
Driver
Thread Starter
#66
Driver School Candidate
#67
Driver
Thread Starter
Then I read somewhere that it happened to more than one person. So, I don't think that was the reason.
#68
Driver
Thread Starter
#70
Driver
Thread Starter
I secured the unit with some brackets I fabricated. It is not moving now in any corner, even if I press so hard.
One peace in the top:
And two "L" shape in the sides :
One peace in the top:
And two "L" shape in the sides :
#72
Driver
Thread Starter
#73
Driver School Candidate
I have one question for the ones that have ML system. I have a 06 GS and i did the camera mod and works perfectly (thank you very much for the post).
How is you sound quality working, i think i´ve lost some sound quality (mainly i guess the bass is too present in the front speaker and distords in some songs). Wich setup are you using for the android EQ and for console settings? I´ve tested with CANBUS setup (GS LO, GS HI) and i would say with LO sounds better. Also, i´ve noticed that the ASL function is on (YES) on console module at low speed but at higher speeds it turns off (NO)
How is you sound quality working, i think i´ve lost some sound quality (mainly i guess the bass is too present in the front speaker and distords in some songs). Wich setup are you using for the android EQ and for console settings? I´ve tested with CANBUS setup (GS LO, GS HI) and i would say with LO sounds better. Also, i´ve noticed that the ASL function is on (YES) on console module at low speed but at higher speeds it turns off (NO)
#74
Driver School Candidate
Join Date: Apr 2020
Location: ca
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
lexis is 350 2007 android tesla unit
Hey does anyone know how to get the air conditioner to connect to the Tesla screen? I plugged in the main stereo harness given but still no ac working. also having trouble with my factor back up camera and my hazards. if there is any video or instructions on the installation. of this 10.4 headhunt pleas let me know.
#75
Driver School Candidate
Join Date: Apr 2020
Location: California
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
I could not find the Television camera controller.
I couldn’t find the television controller. Is there any other way I can locate the wires for the RCA jack?
Hi Everyone,
I will explain how I managed to connect my Tesla Style headunit to the OEM camera in my GS 2006.
My car comes with Mark Levinson System and Navigation. I don't think it will make a defferance, but FYI.
1. Remove the glove compartment to reach the wires coming from the camera to the (Television Camera Controller).
Behind the glove compartment
Television Camera Controller
2. You need one meter long RCA cable and cut the head from one side. Locate pin 39 [CV-] (gray wire) and pin 40 [CV+] (red wire) in the K64 plug. Connect the center wire of the RCA cable to pin 40 and the shield to pin 39. After you finish run the other end of the RCA cable to the headunit and connect it. Make sure if you unplug K64 to plug it back because the OEM camera is taking 6.4v power from pin 20[CB+] and pin 19 [CGND] of K 64.
2006 GS OEM camera connection
K 64
3. Now go behind the Headunit and locate pin 13 [REV] (red wire) in the K 46 plug and connect it to the reverse wire from the Headunit. I used an extention wire to reach it easly.
Reverse Signal comming to the OEM unit
K 46
Reverse and Illumination Wires
Bonus (not related to camera):
Connect pin 12 (green) of K 46 plug to the illumination wire of the Headunit to dim the screen when you turn on the headlight.
I will explain how I managed to connect my Tesla Style headunit to the OEM camera in my GS 2006.
My car comes with Mark Levinson System and Navigation. I don't think it will make a defferance, but FYI.
1. Remove the glove compartment to reach the wires coming from the camera to the (Television Camera Controller).
Behind the glove compartment
Television Camera Controller
2. You need one meter long RCA cable and cut the head from one side. Locate pin 39 [CV-] (gray wire) and pin 40 [CV+] (red wire) in the K64 plug. Connect the center wire of the RCA cable to pin 40 and the shield to pin 39. After you finish run the other end of the RCA cable to the headunit and connect it. Make sure if you unplug K64 to plug it back because the OEM camera is taking 6.4v power from pin 20[CB+] and pin 19 [CGND] of K 64.
2006 GS OEM camera connection
K 64
3. Now go behind the Headunit and locate pin 13 [REV] (red wire) in the K 46 plug and connect it to the reverse wire from the Headunit. I used an extention wire to reach it easly.
Reverse Signal comming to the OEM unit
K 46
Reverse and Illumination Wires
Bonus (not related to camera):
Connect pin 12 (green) of K 46 plug to the illumination wire of the Headunit to dim the screen when you turn on the headlight.