F-Sport fog light retrofit started...
#31
I installed my LED Fogs last night. Had to extend the IJDM wiring harness to the drivers side fog light and I also didn't run my signal wire to the Parking lights. I ran the signal Wire to the Guage Fuse in the drivers side engine fuse panel with a add a circuit. this is a 5 amp factory fuse that is only powered on when the car ignition is on so I can use the fogs independent of the headlights. running the wire through the firewall was easy enough with a metal coat hanger and electrical tape. I am extremely happy with the light output and beam pattern. nice and crisp. and I didn't have any issue the the washer bottle in my 15 other than its a tight fit between the back of the fog light housing and washer bottle. There are no gaps around the lights and the garnish trim and everything fits and works like a charm. I mounted the fog light switch to the left of the steering wheel below the odometer gauge illumination controls with the supplied double sticky back tape.
#34
Instructor
iTrader: (1)
Check with Nigel-jdmparts info@nigel-jdmparts.com
If no luck let me know as i have the part numbers.
If no luck let me know as i have the part numbers.
I just send them an email. Hopefully they will reply.
#35
Instructor
iTrader: (1)
They replied and here's the link for all the options they have.
http://www.nigel-jdmparts.com/index....product_id=161
http://www.nigel-jdmparts.com/index....product_id=161
#36
Lexus Champion
iTrader: (74)
Check with Nigel-jdmparts info@nigel-jdmparts.com
If no luck let me know as i have the part numbers.
If no luck let me know as i have the part numbers.
They replied and here's the link for all the options they have.
http://www.nigel-jdmparts.com/index....product_id=161
http://www.nigel-jdmparts.com/index....product_id=161
#37
Instructor
iTrader: (1)
Check with Nigel-jdmparts info@nigel-jdmparts.com
If no luck let me know as i have the part numbers.
If no luck let me know as i have the part numbers.
Where did you get the coaxial cable?
Last edited by LatinLS430; 10-04-16 at 04:21 PM.
#40
Pole Position
Thread Starter
A little update. The standard bulbs ended up putting dark spots on my Lamin X over time. After going through 2 sets (warrantied via Lamin X) I switched to these bulbs and have been very happy. They generate basically no heat
#41
Anyone know if there are better quality LED lamp housings over OEM? trying to figure out if I want OEM or just a cheap ebay one if OEM isn't that great this is for a 2018
#42
OK, all done. I didn't want to tap or destroy any factory wiring in case, so here is what I did for my trigger wire to work with parking lights. It is actually a strand of wire from a coaxial cable that I clipped and soldered to the multistrand trigger wire then heatshrinked. I also pushed the wire into the weatherproof boot a tad more but forgot a pic so it's actually fully inside the boot now. ( Pics are backwards sorry )
On another note, what would I do differently if I would like the fog lights to turn on with the headlights instead of the DRL? Thanks.
#43
I installed my LED Fogs last night. Had to extend the IJDM wiring harness to the drivers side fog light and I also didn't run my signal wire to the Parking lights. I ran the signal Wire to the Guage Fuse in the drivers side engine fuse panel with a add a circuit. this is a 5 amp factory fuse that is only powered on when the car ignition is on so I can use the fogs independent of the headlights. running the wire through the firewall was easy enough with a metal coat hanger and electrical tape. I am extremely happy with the light output and beam pattern. nice and crisp. and I didn't have any issue the the washer bottle in my 15 other than its a tight fit between the back of the fog light housing and washer bottle. There are no gaps around the lights and the garnish trim and everything fits and works like a charm. I mounted the fog light switch to the left of the steering wheel below the odometer gauge illumination controls with the supplied double sticky back tape.
#45
Where did you get the yellow fogs for your '06? Did you install Lamin-X over the Morimotos?