What did you do to your GS today?
#211
Driver School Candidate
Beautiful day here in Houston so I took the time to give her a bath, instead of the typical trip to the car wash. Gleaming and ready to go for the weekend...
The following users liked this post:
GSLexTexas (04-12-17)
#212
Lexus Champion
I changed the front turn signals with iJDMtoy LEDs with decoder boxes early when I got my 2017 GS (hated how OEM were incandescent). I always felt they were not as bright as I wanted, didn't like how it looked under the hood, didn't like how connectors were slightly exposed, and didn't like how the mount is rubber and doesn't lock in place like OEM. I ordered the iJDMtoy No Resistor LEDs to replace them and installed them today. These are signicantly brighter and I'm able to use the OEM mount (looks OEM outside and under the hood). The website says that it will hyperflash after 8 mins, but I left them on for more than 15 minutes and they never did. Now my GS no longer has any incandescent bulbs, and now all lights are LED (which is how it should've been).
The following users liked this post:
and3re (05-19-17)
#213
Replaced the original tires with Michelin Primacy MXM4. Old Dunlops SP SPort had 42K and probably another 8K miles left but couldn't take them anymore. Not an aggressive driver so prefer the more touring tire for ride and quiet. Glad I did. Dealer wanted $300 more to replace so went with a local chain who did them for $1K complete and best yet 2 minutes from home and only took 30 minutes.
The following 6 users liked this post by comtrans:
alpha0M3G4 (04-10-17),
gnc1017 (11-30-19),
itjustme (04-12-17),
kode3 (01-30-19),
Pacman9270 (12-10-17),
and 1 others liked this post.
The following users liked this post:
dTxworld (12-06-18)
#217
Driver School Candidate
Lowered on Tanabe springs and Ichiba spacers. Also fixed my driver side door buzz
Attachment 407554
Attachment 407555
Attachment 407554
Attachment 407555
Looks good. Assuming no issues with rubbing?
#220
Lexus Test Driver
iTrader: (1)
I have a 2013 with the moonroof wind noise issue. I took the moonroof glass out and replaced the seal. The new seal is thicker on the back portion(Toyota/Lexus) updated the seal, even though the part number is the same.
Just raise the moon roof glass, take the plastic covers off, and just 4 torex bolts hold it on.
When reinstalling, loosely tighten the torex bolts and close the moonroof. Then adjust each corner/tighten the torex bolt so the seal is flush with the roof.
Easy job took me 45 minutes being very careful.
I also used resolve carpet stain remove to remove a few marks in the headliner from previous owner and a grease spot I made changing the seal. Took all the stains out and no discoloration.
Just raise the moon roof glass, take the plastic covers off, and just 4 torex bolts hold it on.
When reinstalling, loosely tighten the torex bolts and close the moonroof. Then adjust each corner/tighten the torex bolt so the seal is flush with the roof.
Easy job took me 45 minutes being very careful.
I also used resolve carpet stain remove to remove a few marks in the headliner from previous owner and a grease spot I made changing the seal. Took all the stains out and no discoloration.
The following users liked this post:
LatinLS430 (04-12-17)
#221
I have a 2013 with the moonroof wind noise issue. I took the moonroof glass out and replaced the seal. The new seal is thicker on the back portion(Toyota/Lexus) updated the seal, even though the part number is the same.
Just raise the moon roof glass, take the plastic covers off, and just 4 torex bolts hold it on.
When reinstalling, loosely tighten the torex bolts and close the moonroof. Then adjust each corner/tighten the torex bolt so the seal is flush with the roof.
Easy job took me 45 minutes being very careful.
I also used resolve carpet stain remove to remove a few marks in the headliner from previous owner and a grease spot I made changing the seal. Took all the stains out and no discoloration.
Just raise the moon roof glass, take the plastic covers off, and just 4 torex bolts hold it on.
When reinstalling, loosely tighten the torex bolts and close the moonroof. Then adjust each corner/tighten the torex bolt so the seal is flush with the roof.
Easy job took me 45 minutes being very careful.
I also used resolve carpet stain remove to remove a few marks in the headliner from previous owner and a grease spot I made changing the seal. Took all the stains out and no discoloration.
#223
Attachment 407671SSR SP1's are finally on! 😁 Will take more pics this weekend.
Quick question - are your window visors JDM or other?
#224
Other mods: Airrunner Suspension, Airlift Management 3H, toms intake filter, joe-z full catback, 2mm spacers, and SPC rear camber arms.
Future mods: aimgain non-fsport kit and hps intake.
The following users liked this post:
Nigel-JDMParts (04-14-17)