Front Apron Separation?
#301
Instructor
I can confirm the fenders are different. The bumper is actually 2 inches longer, but the actual front part is exactly the same (the headlights are also 2 inches away from the car), so it's basically both sides of the bumper that are stretched, so this means the fender/bumper angle isn't the same.
#302
Pole Position
Thread Starter
Constant hard starts, constant manual shifts points right before the rev limiter, constant mountain carvings, constant high rate of speed…
My car constantly gets a full workout and mine is fine. 🤷🏽♂️
8300 glorious miles since March 4th and I love this beast more everyday.
The following users liked this post:
wthrman2 (10-08-22)
#303
Pole Position
#304
As if this thread won't die. I went over a hard bump in the road (where a bridge meets the road, a particularly harsh transition) and came home to see the driver side apron slightly sagging as in all the photos others have shared.
I do not believe this is related to the torque of the engine, but rather a simple clip failure. The clip just seems unable to handle the extra mass/lever arm of the extended fanders.
Anyway, old news. No one cares
I do not believe this is related to the torque of the engine, but rather a simple clip failure. The clip just seems unable to handle the extra mass/lever arm of the extended fanders.
Anyway, old news. No one cares
The following users liked this post:
giS (10-20-22)
#305
Intermediate
As if this thread won't die. I went over a hard bump in the road (where a bridge meets the road, a particularly harsh transition) and came home to see the driver side apron slightly sagging as in all the photos others have shared.
I do not believe this is related to the torque of the engine, but rather a simple clip failure. The clip just seems unable to handle the extra mass/lever arm of the extended fanders.
Anyway, old news. No one cares
I do not believe this is related to the torque of the engine, but rather a simple clip failure. The clip just seems unable to handle the extra mass/lever arm of the extended fanders.
Anyway, old news. No one cares
#306
Pole Position
Thread Starter
We have some movement! Ryan posted this to our car group:
“Confirmed my bumper was replaced to be sent to Japan R&D. The retaining clips are suspected to be out of spec - the manufacturer is checking tolerances on the plastic retaining clips (they are not made by Lexus where the bumper is).They think only some of their stock of the retainers are out of spec.”
“Confirmed my bumper was replaced to be sent to Japan R&D. The retaining clips are suspected to be out of spec - the manufacturer is checking tolerances on the plastic retaining clips (they are not made by Lexus where the bumper is).They think only some of their stock of the retainers are out of spec.”
#307
Intermediate
We have some movement! Ryan posted this to our car group:
“Confirmed my bumper was replaced to be sent to Japan R&D. The retaining clips are suspected to be out of spec - the manufacturer is checking tolerances on the plastic retaining clips (they are not made by Lexus where the bumper is).They think only some of their stock of the retainers are out of spec.”
“Confirmed my bumper was replaced to be sent to Japan R&D. The retaining clips are suspected to be out of spec - the manufacturer is checking tolerances on the plastic retaining clips (they are not made by Lexus where the bumper is).They think only some of their stock of the retainers are out of spec.”
The following users liked this post:
DLPTony (10-26-22)
The following 6 users liked this post by AmbyBomb:
Carolina50 (10-26-22),
DLPTony (10-27-22),
giS (10-26-22),
jororo (10-29-22),
TipsyTonio (10-27-22),
and 1 others liked this post.
#309
Intermediate
The following 3 users liked this post by giS:
The following 2 users liked this post by AmbyBomb:
Carolina50 (10-26-22),
DLPTony (10-27-22)
#312
We have some movement! Ryan posted this to our car group:
“Confirmed my bumper was replaced to be sent to Japan R&D. The retaining clips are suspected to be out of spec - the manufacturer is checking tolerances on the plastic retaining clips (they are not made by Lexus where the bumper is).They think only some of their stock of the retainers are out of spec.”
“Confirmed my bumper was replaced to be sent to Japan R&D. The retaining clips are suspected to be out of spec - the manufacturer is checking tolerances on the plastic retaining clips (they are not made by Lexus where the bumper is).They think only some of their stock of the retainers are out of spec.”
The following users liked this post:
DLPTony (10-27-22)
#313
Pole Position
Thread Starter
Too bad *he* can’t see this… I want to say: “All that time pontificating, now what?” 😎
Right!! At any good dinner party, I’ll sit next to the Sarcasm Contingent every freaking time. 😈
Always. 👍🏽
The following 2 users liked this post by DLPTony:
giS (10-27-22),
TipsyTonio (10-27-22)
#314
Racer
The following 3 users liked this post by TipsyTonio:
#315
Pole Position
Thread Starter
The following 3 users liked this post by DLPTony: