HKS SSM IS F Exhaust Pics Inside!
#17
Pole Position
iTrader: (1)
Join Date: Aug 2002
Location: France
Posts: 252
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://www.clublexus.com/forums/images/icons/icon1.gif)
The quality looks fantastic. I just wondered why they have only 1 pipe at the exit if the want to keep the standard stacked diffuser
The design is very similar to the Suruga Speed exhaust, it should keep the noise level very low and if the power gain is similar as well it would be a very interesting option, Suruga being quite expensive with the shipping and taxes from Japan
The design is very similar to the Suruga Speed exhaust, it should keep the noise level very low and if the power gain is similar as well it would be a very interesting option, Suruga being quite expensive with the shipping and taxes from Japan
#27
![Default](https://www.clublexus.com/forums/images/icons/icon1.gif)
Well I am not sure what to think. Based on the proto I built with straight HKS Ti cans there is not much drone at all with a straight muffler, so not sure what tone they are shooting for. The extra bends will add some cancellation, basically like a muffler outside the muffler, but I think with the added bracing etc, its going to be very close to stock weight unless they used a thin wall Stainless, like 0.032".
Props to them for doing a stainless casting for the stock ball flange, I just had custom ball flanges spun, and for robotic welding everything. The hollow hangers are also something I tried to do also to save weight.
I am going to make a bet that given the investment its going to be north of $1K but maybe it will be a nice surprise. The speculation about the musical instrument shapes adding to the tone are somewhat true however not in the classical sense of an instrument. An instrument has a gradually tapered design that amplifies sound through constructive resonance. This design is trying to do the opposite and it needs more tubing length to achieve more destructive interference. Most of the tone will come from the difference in length of the two sides or the syncopation of the resulting two tones out of each side. It could sound pretty interesting if the two sides are delay enough WRT to eachother.
To comment on the performance of my straight pipe Ti design, it netted peak gains (at peak RPM) of 8WHP. Things were pretty well offset from 3500 up so a good area of gains overall. Not much you say, but keep in mind the weight savings is much more important that the net numbers. The diffuser effect is also not measured on a dyno either so that bears mentioning.
Tracking this thread to see of people are still interested in an axle back design and what the end price will be. Thanks for the post and pics.
Fig
Props to them for doing a stainless casting for the stock ball flange, I just had custom ball flanges spun, and for robotic welding everything. The hollow hangers are also something I tried to do also to save weight.
I am going to make a bet that given the investment its going to be north of $1K but maybe it will be a nice surprise. The speculation about the musical instrument shapes adding to the tone are somewhat true however not in the classical sense of an instrument. An instrument has a gradually tapered design that amplifies sound through constructive resonance. This design is trying to do the opposite and it needs more tubing length to achieve more destructive interference. Most of the tone will come from the difference in length of the two sides or the syncopation of the resulting two tones out of each side. It could sound pretty interesting if the two sides are delay enough WRT to eachother.
To comment on the performance of my straight pipe Ti design, it netted peak gains (at peak RPM) of 8WHP. Things were pretty well offset from 3500 up so a good area of gains overall. Not much you say, but keep in mind the weight savings is much more important that the net numbers. The diffuser effect is also not measured on a dyno either so that bears mentioning.
Tracking this thread to see of people are still interested in an axle back design and what the end price will be. Thanks for the post and pics.
Fig
__________________
Redefining Lexus Aftermarket Parts Since 2001
-- We are your Lexus suspension experts--
BCR - KW - PENSKE - OHLINS - HKS - GREDDY - STANCEPARTS
Links - Arms - SuperPro Poly Bushings - Solid Bearing Conversions - Motor Mounts
RB BBK's and 2P Rotors, G-Loc pads, Radium Fuel Systems
Custom Fabrication Design and Machining - Industrial 3D Printing - Laser Cutting
2018 USTCC Sportsman Class Champions - 2018 NASA ST5 National Champions
Redefining Lexus Aftermarket Parts Since 2001
-- We are your Lexus suspension experts--
BCR - KW - PENSKE - OHLINS - HKS - GREDDY - STANCEPARTS
Links - Arms - SuperPro Poly Bushings - Solid Bearing Conversions - Motor Mounts
RB BBK's and 2P Rotors, G-Loc pads, Radium Fuel Systems
Custom Fabrication Design and Machining - Industrial 3D Printing - Laser Cutting
2018 USTCC Sportsman Class Champions - 2018 NASA ST5 National Champions
![](https://www.clublexus.com/forums/signaturepics/sigpic106840_3.gif)
#29
![Default](https://www.clublexus.com/forums/images/icons/icon1.gif)
Thanks for all of the kind words and interest in the R & D being done by HKS for the IS F exhaust.
The folks at HKS are well aware of this thread too.
I'll be picking up my car either tomorrow or Saturday from them. Once I go over all of the details I will post what I know.
![Thumb Up](https://www.clublexus.com/forums/images/smilies/thumbsup.gif)
I'll be picking up my car either tomorrow or Saturday from them. Once I go over all of the details I will post what I know.