Pic of your IS-F - RIGHT NOW!
#7711
Driver
iTrader: (4)
Lol it was fun, hardest part was just maneuvering the manifold from the harness. I replaced 4 of the direct injector connectors and some of the port injector connectors. Oddly enough I ordered the exact amount of connectors I anticipated I might break. Taking off all the supercharger piping wasn’t fun though.
#7712
Lol it was fun, hardest part was just maneuvering the manifold from the harness. I replaced 4 of the direct injector connectors and some of the port injector connectors. Oddly enough I ordered the exact amount of connectors I anticipated I might break. Taking off all the supercharger piping wasn’t fun though.
#7713
Tech Info Resource
iTrader: (2)
Lol it was fun, hardest part was just maneuvering the manifold from the harness. I replaced 4 of the direct injector connectors and some of the port injector connectors. Oddly enough I ordered the exact amount of connectors I anticipated I might break. Taking off all the supercharger piping wasn’t fun though.
#7715
Spent some quality time in the garage working on the IS F last couple days.
Varex installed & changed the spark plugs. Felt good to wrench after a long winter. Need to change the oil too but ran out of time.
Varex installed & changed the spark plugs. Felt good to wrench after a long winter. Need to change the oil too but ran out of time.
The following 5 users liked this post by b15:
BS ISF (03-30-23),
iH8RICERZ (03-29-23),
MileHIFcar (03-29-23),
msgs350 (03-29-23),
RJMacReady (03-31-23)
#7717
Just patience and having the right tools. Oh and a nice beverage Everything is tight so you'll have to get creative in how you access some of them. Straight forward overall, just don't drop the bolt that holds the coil in like I did. It happened on the 8th one too, just my luck.
Still way easier than the rear bank of a transversely mounted v6.
Still way easier than the rear bank of a transversely mounted v6.
#7718
Intermediate
How was the exhaust install fitment etc?...mine should be here today/tommorrow
#7720
Key is to put it together loosely, then jack it up and tighten it section by section from front to back.
The following 2 users liked this post by b15:
inovashn (03-30-23),
RJMacReady (03-31-23)
#7721
Intermediate
Install was straight forward. Had to trim the both tips but no other issues. Mine cleared the round cross brace but barely so I spaced it .5" anyways to avoid any banging.
Key is to put it together loosely, then jack it up and tighten it section by section from front to back.
Key is to put it together loosely, then jack it up and tighten it section by section from front to back.
The following 3 users liked this post by DownUnder:
#7722
Intermediate
The following 5 users liked this post by Sgt350:
BS ISF (04-03-23),
Cerevo (04-02-23),
iH8RICERZ (04-02-23),
Rickna (04-03-23),
TheNaeblis (04-05-23)
The following 6 users liked this post by panita2010:
BS ISF (04-05-23),
Cerevo (04-05-23),
iH8RICERZ (04-05-23),
Rickna (04-05-23),
SonicRob99 (04-07-23),
and 1 others liked this post.
The following 6 users liked this post by Cerevo:
BS ISF (04-05-23),
iH8RICERZ (04-05-23),
msgs350 (04-05-23),
panita2010 (04-05-23),
Rickna (04-05-23),
and 1 others liked this post.