CA New GTE internals (rods, pistons, bearings), USED Megan Y-pipe, Exhaust for turbo
#1
Pole Position
Thread Starter
New GTE internals (rods, pistons, bearings), USED Megan Y-pipe, Exhaust for turbo
Located in Socal 805/818 area. (Mods let me know if I need a vouch)
Y-Pipe SOLD
I bought these off of another member from my.IS a few months back. Plans have changed, decided to go with forged internals and high boost. These guys are boxed and ready to ship.
$500 shipped/PP'd Send as gift to waive the 3% PP fee, or send as a regular transaction with 3% fee on top.
And Finally I have my old exhaust set up from when I first boosted. It's a Tanabe Concept G catback made for N/A set up with a 3" pipe welded over to mate to the 3" downpipe. I painted the tip black to stay low from cops. If you're not turbo'd and want a Tanabe exhaust you can always have a shop chop the 3" pipe off and weld new pipe to your OEM/aftermarket Y-pipe. Anyways, there were no leaks or anything like that, I just wanted something more stealthy to replace it. This is a big piece so I'm not sure how much shipping will be. I'd like to have local pick up, but I doubt that will happen...I will ship at buyer's expense though.
$350 PP'd + shipping
How it looked on the car:
I wish I had better videos with the old exhaust set up...This is all I got so bare with me.
YouTube - IS300 turbo 0-110
YouTube - IS300 Turbo Quick Run
And this lol, I took this video while the paint was drying on the muffler. Same exhaust note, just a little louder than with the muffler on...
YouTube - IS300 Turbo No Axle Back
2 pieces: Muffler/piping
Thanks for looking guys
Y-Pipe SOLD
I bought these off of another member from my.IS a few months back. Plans have changed, decided to go with forged internals and high boost. These guys are boxed and ready to ship.
$500 shipped/PP'd Send as gift to waive the 3% PP fee, or send as a regular transaction with 3% fee on top.
And Finally I have my old exhaust set up from when I first boosted. It's a Tanabe Concept G catback made for N/A set up with a 3" pipe welded over to mate to the 3" downpipe. I painted the tip black to stay low from cops. If you're not turbo'd and want a Tanabe exhaust you can always have a shop chop the 3" pipe off and weld new pipe to your OEM/aftermarket Y-pipe. Anyways, there were no leaks or anything like that, I just wanted something more stealthy to replace it. This is a big piece so I'm not sure how much shipping will be. I'd like to have local pick up, but I doubt that will happen...I will ship at buyer's expense though.
$350 PP'd + shipping
How it looked on the car:
I wish I had better videos with the old exhaust set up...This is all I got so bare with me.
YouTube - IS300 turbo 0-110
YouTube - IS300 Turbo Quick Run
And this lol, I took this video while the paint was drying on the muffler. Same exhaust note, just a little louder than with the muffler on...
YouTube - IS300 Turbo No Axle Back
2 pieces: Muffler/piping
Thanks for looking guys
Last edited by madchyers; 05-07-11 at 02:24 PM.
Thread
Thread Starter
Forum
Replies
Last Post
BGinLA
SC430 - 2nd Gen (2001-2010)
27
03-19-19 07:29 PM
ImportISF
2Gen IS250 / IS350 / IS-F Classifieds (06-13)
5
11-11-12 08:44 AM
DryBlaze
SC400 / 300 Classifieds
12
02-23-08 03:09 PM