♫ DO™ - Picture Me Rollin' ♫
07-28-09, 08:12 AM
#36
Pole Position
iTrader: (5)
Join Date: Jun 2008
Location: Killeen, TX
Posts: 260
Likes: 0
Received 0 Likes
on
0 Posts
). And yeah the exhaust tips do look a little too large for the car. I think asize smaller and in oval will compliment the set up more.
07-28-09, 12:13 PM
#38
Driver
Thread Starter
Join Date: Feb 2008
Location: Georgia
Posts: 142
Likes: 0
Received 0 Likes
on
0 Posts
gee wizz!!! thank you guys sooooooo much for the barrage of feedback. it means a lot! 
but yeah... i have my thoughts about the grille as well but as someone said somewhere we really dont have that many options as far as affordable aftermarket support is concerned and i'm not in the position to dish out $500+ on a Fabulous (pun intended) grille. i may end up selling this after i fabricate one with my old OEM shroud but until i get off my *** and do so I'll be stuck with this.
as far as spacing out the wheels a tad. i may never do it with these wheels unless i get a smaller tire. and the wheels are but a mere 18x8 +38 (with a 25mm spacer = +13) & +26 (with a 15mm spacer = +11).
i'd love to run a 205 or 215/40 all the way around but i feel it'll make the wheel look even SMALLER in width than they already are
my hope is to sell these and get something with a more desirable width. in possibly +10 for the front and +8 for the rear and THEN i'll take upon the roll of Leonardo DiCaprio in Titanic... (King of the Woooooooooorld!)
but yeah... i have my thoughts about the grille as well but as someone said somewhere we really dont have that many options as far as affordable aftermarket support is concerned and i'm not in the position to dish out $500+ on a Fabulous (pun intended) grille. i may end up selling this after i fabricate one with my old OEM shroud but until i get off my *** and do so I'll be stuck with this.
as far as spacing out the wheels a tad. i may never do it with these wheels unless i get a smaller tire. and the wheels are but a mere 18x8 +38 (with a 25mm spacer = +13) & +26 (with a 15mm spacer = +11).
i'd love to run a 205 or 215/40 all the way around but i feel it'll make the wheel look even SMALLER in width than they already are
my hope is to sell these and get something with a more desirable width. in possibly +10 for the front and +8 for the rear and THEN i'll take upon the roll of Leonardo DiCaprio in Titanic... (King of the Woooooooooorld!)
Last edited by D.O.; 07-28-09 at 12:20 PM.
07-28-09, 01:43 PM
#40
Driver
Thread Starter
Join Date: Feb 2008
Location: Georgia
Posts: 142
Likes: 0
Received 0 Likes
on
0 Posts
and i frickin LOVE my tips! i like the exaggerated look of it. and the sound is even BETTER! i'll record it tonight for you'z guys
but yeah... i could have done even MORE modifying if you didnt sell your Megans to someone unlocally (if thats even a word)
07-29-09, 09:26 AM
#42
Driver
Thread Starter
Join Date: Feb 2008
Location: Georgia
Posts: 142
Likes: 0
Received 0 Likes
on
0 Posts
but... i figured i'd toss up the last 3 shots from that rolling session. 
07-31-09, 07:42 AM
#44
07-31-09, 07:47 AM
#45
Driver
Thread Starter
Join Date: Feb 2008
Location: Georgia
Posts: 142
Likes: 0
Received 0 Likes
on
0 Posts