Programming a key for a 1999 LS400, is this correct?
#1
Programming a key for a 1999 LS400, is this correct?
Tried this procedure below and it doesn't seem to be working. Is it correct?
A. Before starting the programming procedures, make sure to SET UP the vehicle as follows.
1. Remove Key from ignition
2. CLOSE AND LOCK ALL THE DOORS (this is the missing step)
3. Manually unlock and open the driver's door only
---------------------------------------------------------------
1. Driver's door OPEN and unlocked, all other doors closed and locked.
2. Insert YOUR key in ignition, DO NOT TURN, remove key.
3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly
press
lock and unlock 5 times (count the lock 5 times and unlock 5 times).
4. Shut door.
5. Open door.
6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock
and unlock 5 times (count the lock 5 times and unlock 5 times).
7. With the door open insert your key into the ignition, turn to on
position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once). If
they
don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second,
release.
The locks should cycle once. If not, start over and go slower.
10. Close the door. Open the door. Press the lock button on the remote.
The locks should cycle. Close the door. Press the lock button on the
remote, the doors should lock. Press again and the doors should
unlock.
A. Before starting the programming procedures, make sure to SET UP the vehicle as follows.
1. Remove Key from ignition
2. CLOSE AND LOCK ALL THE DOORS (this is the missing step)
3. Manually unlock and open the driver's door only
---------------------------------------------------------------
1. Driver's door OPEN and unlocked, all other doors closed and locked.
2. Insert YOUR key in ignition, DO NOT TURN, remove key.
3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly
press
lock and unlock 5 times (count the lock 5 times and unlock 5 times).
4. Shut door.
5. Open door.
6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock
and unlock 5 times (count the lock 5 times and unlock 5 times).
7. With the door open insert your key into the ignition, turn to on
position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once). If
they
don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second,
release.
The locks should cycle once. If not, start over and go slower.
10. Close the door. Open the door. Press the lock button on the remote.
The locks should cycle. Close the door. Press the lock button on the
remote, the doors should lock. Press again and the doors should
unlock.
#2
The official key programming instructions have been posted many times in the past including by me in the following thread: https://www.clublexus.com/forums/ls4...y-dilemma.html
#4
Tried this procedure below and it doesn't seem to be working. Is it correct?
A. Before starting the programming procedures, make sure to SET UP the vehicle as follows.
1. Remove Key from ignition
2. CLOSE AND LOCK ALL THE DOORS (this is the missing step)
3. Manually unlock and open the driver's door only
---------------------------------------------------------------
1. Driver's door OPEN and unlocked, all other doors closed and locked.
2. Insert YOUR key in ignition, DO NOT TURN, remove key.
3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly
press
lock and unlock 5 times (count the lock 5 times and unlock 5 times).
4. Shut door.
5. Open door.
6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock
and unlock 5 times (count the lock 5 times and unlock 5 times).
7. With the door open insert your key into the ignition, turn to on
position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once). If
they
don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second,
release.
The locks should cycle once. If not, start over and go slower.
10. Close the door. Open the door. Press the lock button on the remote.
The locks should cycle. Close the door. Press the lock button on the
remote, the doors should lock. Press again and the doors should
unlock.
A. Before starting the programming procedures, make sure to SET UP the vehicle as follows.
1. Remove Key from ignition
2. CLOSE AND LOCK ALL THE DOORS (this is the missing step)
3. Manually unlock and open the driver's door only
---------------------------------------------------------------
1. Driver's door OPEN and unlocked, all other doors closed and locked.
2. Insert YOUR key in ignition, DO NOT TURN, remove key.
3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly
press
lock and unlock 5 times (count the lock 5 times and unlock 5 times).
4. Shut door.
5. Open door.
6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock
and unlock 5 times (count the lock 5 times and unlock 5 times).
7. With the door open insert your key into the ignition, turn to on
position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once). If
they
don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second,
release.
The locks should cycle once. If not, start over and go slower.
10. Close the door. Open the door. Press the lock button on the remote.
The locks should cycle. Close the door. Press the lock button on the
remote, the doors should lock. Press again and the doors should
unlock.
Thank you!
#5
Tried this procedure below and it doesn't seem to be working. Is it correct?
A. Before starting the programming procedures, make sure to SET UP the vehicle as follows.
1. Remove Key from ignition
2. CLOSE AND LOCK ALL THE DOORS (this is the missing step)
3. Manually unlock and open the driver's door only
---------------------------------------------------------------
1. Driver's door OPEN and unlocked, all other doors closed and locked.
2. Insert YOUR key in ignition, DO NOT TURN, remove key.
3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly
press
lock and unlock 5 times (count the lock 5 times and unlock 5 times).
4. Shut door.
5. Open door.
6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock
and unlock 5 times (count the lock 5 times and unlock 5 times).
7. With the door open insert your key into the ignition, turn to on
position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once). If
they
don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second,
release.
The locks should cycle once. If not, start over and go slower.
10. Close the door. Open the door. Press the lock button on the remote.
The locks should cycle. Close the door. Press the lock button on the
remote, the doors should lock. Press again and the doors should
unlock.
A. Before starting the programming procedures, make sure to SET UP the vehicle as follows.
1. Remove Key from ignition
2. CLOSE AND LOCK ALL THE DOORS (this is the missing step)
3. Manually unlock and open the driver's door only
---------------------------------------------------------------
1. Driver's door OPEN and unlocked, all other doors closed and locked.
2. Insert YOUR key in ignition, DO NOT TURN, remove key.
3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly
press
lock and unlock 5 times (count the lock 5 times and unlock 5 times).
4. Shut door.
5. Open door.
6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock
and unlock 5 times (count the lock 5 times and unlock 5 times).
7. With the door open insert your key into the ignition, turn to on
position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once). If
they
don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second,
release.
The locks should cycle once. If not, start over and go slower.
10. Close the door. Open the door. Press the lock button on the remote.
The locks should cycle. Close the door. Press the lock button on the
remote, the doors should lock. Press again and the doors should
unlock.
#6
Please let us know if you are able to successfully get the lock/unlock feature to work via the remote. I have tried the official instructions but never could get the lock/unlock buttons to work on my replacement key. I was able to get it to start the car but the buttons are still unresponsive. Very curious if you can get it to work. thanks
There's also a helpful note about following those instructions. I've used it myself a few times over the years and can confirm they work.
#7
For some reason it won't work on my 99
Once I get to f and press the 2 buttons, then the lock button nothing happens.
Maybe cuz the chip in here isn't compatible? https://www.remotesremotes.com/product-p/L_1512V-4BTN-KEY.htm?gclid=CjwKCAjw-8nbBRBnEiwAqWt1zdaE9XnpXVWlpT_gMQi5jVFBVyCjq3iElDqqB4MBFKtrejvESb5qAhoCNbEQAvD_BwE
Got it from here
Once I get to f and press the 2 buttons, then the lock button nothing happens.
Maybe cuz the chip in here isn't compatible? https://www.remotesremotes.com/product-p/L_1512V-4BTN-KEY.htm?gclid=CjwKCAjw-8nbBRBnEiwAqWt1zdaE9XnpXVWlpT_gMQi5jVFBVyCjq3iElDqqB4MBFKtrejvESb5qAhoCNbEQAvD_BwE
Got it from here
Last edited by Sin1UZFE; 09-24-18 at 03:29 PM.
Trending Topics
#8
For some reason it won't work on my 99
Once I get to f and press the 2 buttons, then the lock button nothing happens.
Maybe cuz the chip in here isn't compatible? https://www.remotesremotes.com/produ...hoCNbEQAvD_BwE
Got it from here
Once I get to f and press the 2 buttons, then the lock button nothing happens.
Maybe cuz the chip in here isn't compatible? https://www.remotesremotes.com/produ...hoCNbEQAvD_BwE
Got it from here
You may need help from Yamae.
Last edited by spuds; 09-24-18 at 08:44 PM.
#9
Chips need to match.Threads on here to tell what chip you have,and what to order when you order a new transponder if yours arent matched.My fob reads HYQ1512V on my 98,sounds to me you have the right transponder. Maybe try some of the other peoples instructions and try those? There are some variations that have worked for others.
You may need help from Yamae.
You may need help from Yamae.
#10
Chips need to match.Threads on here to tell what chip you have,and what to order when you order a new transponder if yours arent matched.My fob reads HYQ1512V on my 98,sounds to me you have the right transponder. Maybe try some of the other peoples instructions and try those? There are some variations that have worked for others.
You may need help from Yamae.
You may need help from Yamae.
thanks
#11
Where is the HYQ1512V located on the master key? my 20 year old oem master key does not have any markings on it., I also ordered a replacement key a awhile ago but have not been able to get it to unlock/lock the car. I was able to get it to start the car successfully. Wondering if i ordered the wrong key?
thanks
thanks
The following users liked this post:
saleenssc (12-07-18)
#13
for keys that you want to be able to start your car with, you need to program the transponder recognition into the security system. the remote control for the doorlocks is a separate system. you can get as many keys cut as you like, and they will unlock your doors and the trunks by using them, but until the transponder in the key head is recognized to the security system, they won't start the car.
#14
for keys that you want to be able to start your car with, you need to program the transponder recognition into the security system. the remote control for the doorlocks is a separate system. you can get as many keys cut as you like, and they will unlock your doors and the trunks by using them, but until the transponder in the key head is recognized to the security system, they won't start the car.
https://photos.app.goo.gl/3vyC7iDsdv7cJjQXA
#15
valet keys also do have transponders in them, but they are cut differently so they cannot be used on the gas/trunk lock switch, the glove box, or the trunk. this is so the valet can enter the car, using the key, and start and drive the car in his job, but cannot unlock the gas/trunk lock, if the lock button is pushed, nor get into the trunk or glove box, if the glove box is locked with a master key. i think 1998 and on, lexus went to using keys with the remote controls built in, before, just key and remote separate as a fob. if the key you have can open/unlock all of the above, then it's a master.