LS 430 Door Lock Actuator Tutorial
#91
Driver School Candidate
Join Date: Oct 2012
Location: ca
Posts: 41
Likes: 0
Received 0 Likes
on
0 Posts
Same here, 4 doors, 3 hours. I started at the rear driver door, then rear passenger, front driver, front passenger. Seems odd that they were all acting up at once, but $17, 3 hours and no blood or cussing--which is amazing for me.
On the first one, I pulled the screw out of the door striker which was a mistake as the spring took off. I got it back together fairly easily though. I think I had the last one done in 25 mins. with 8 mins of filing the shaft. I used a small hobby vise on the disassembled motor. I was just going to use the old shaft and winding but too it did not fit quite right, the shaft had a large thing where the brushes connect. I also had trouble with the zip ties as they interfered with the plastic shrouding, so I used glue.
Overall a very satisfying project. Thanks OP. I was thinking about dumping the car as I am now at 150K, but I just can't justify it as it is still in near perfect condition.
On the first one, I pulled the screw out of the door striker which was a mistake as the spring took off. I got it back together fairly easily though. I think I had the last one done in 25 mins. with 8 mins of filing the shaft. I used a small hobby vise on the disassembled motor. I was just going to use the old shaft and winding but too it did not fit quite right, the shaft had a large thing where the brushes connect. I also had trouble with the zip ties as they interfered with the plastic shrouding, so I used glue.
Overall a very satisfying project. Thanks OP. I was thinking about dumping the car as I am now at 150K, but I just can't justify it as it is still in near perfect condition.
#93
Driver School Candidate
Join Date: Feb 2013
Location: North Carolina
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Replaced the actuator motor; lock not fixed
I just took a stab at this... completed the project in just over 2 hours. But I guess I can't say "complete" unless it fixed my problem.
My front, driver's side door still doesn't lock/unlock with the remote. In fact, none of the doors will lock unless I first lock the driver's door manually; then the other three doors will lock with the remote. Same is true when unlocking. I was REALLY hoping that replacing the motor inside the actuator was going to be the fix... perhaps I did something wrong? Or is there something else I should look at?
Now that I've removed and installed the actuator once, I'm sure I can do it again in less than an hour.
My front, driver's side door still doesn't lock/unlock with the remote. In fact, none of the doors will lock unless I first lock the driver's door manually; then the other three doors will lock with the remote. Same is true when unlocking. I was REALLY hoping that replacing the motor inside the actuator was going to be the fix... perhaps I did something wrong? Or is there something else I should look at?
Now that I've removed and installed the actuator once, I'm sure I can do it again in less than an hour.
#94
Driver School Candidate
Join Date: Feb 2013
Location: North Carolina
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Actuator motors
Although my door lock problem was not resolved by replacing the actuator motor, I would like to share with the group my source for the motors, the part number and how easy it was to file the shaft. I read a lot of comments about swapping motor parts to preserve the original "D" shaft... grinding the shaft on the motor was super easy. Of course, you must own or have access to a grinder. If you don't, I recommend buying one. Think of the money you're saving from tackling this project yourself and apply some of that saved money towards a grinder or a dremel. These tools will pay for themselves many times over!
Here's the ebay auction and part number:
4 pk MABUCHI CAR DOOR LOCK MOTORS - DIY ACTUATOR REPAIR Toyota Lexus Honda Ford
http://www.ebay.com/itm/4-pk-MABUCHI...34ae58&vxp=mtr
Manufacturer Part Number: FC-280PC-22125
Interchange Part Number: FC-280PT-22125
Other Part Number: KF243G-101
SIZE SPECIFICATIONS:
Shaft: ROUND - 2mm diameter x 9.85mm length
Canister: 24.2mm Diameter (18.3mm on flat sides) x 30.5mm long
Overall Length: 45.0mm (Tip to Tail)
Here's the ebay auction and part number:
4 pk MABUCHI CAR DOOR LOCK MOTORS - DIY ACTUATOR REPAIR Toyota Lexus Honda Ford
http://www.ebay.com/itm/4-pk-MABUCHI...34ae58&vxp=mtr
Manufacturer Part Number: FC-280PC-22125
Interchange Part Number: FC-280PT-22125
Other Part Number: KF243G-101
SIZE SPECIFICATIONS:
Shaft: ROUND - 2mm diameter x 9.85mm length
Canister: 24.2mm Diameter (18.3mm on flat sides) x 30.5mm long
Overall Length: 45.0mm (Tip to Tail)
#96
Driver School Candidate
Join Date: Feb 2013
Location: North Carolina
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Door Lock Resolution
After giving it the 'ol college try to repair my lock by replacing the cheap little motor (didn't work for me)... I ultimately purchased a NEW actuator from an online parts dealer. Cost ~$220 or something like that. Total installation took ~45 minutes since I had already performed the ritual once before. Problem solved. I think the original contributor to this thread did the same thing. All door locks are now functioning and I'm happy. Just wished I could have solved the problem with a $4 motor, instead. Good luck to anyone attempting this repair and THANK YOU to everyone who has contributed to this thread.
#98
Driver School Candidate
After giving it the 'ol college try to repair my lock by replacing the cheap little motor (didn't work for me)... I ultimately purchased a NEW actuator from an online parts dealer. Cost ~$220 or something like that. Total installation took ~45 minutes since I had already performed the ritual once before. Problem solved. I think the original contributor to this thread did the same thing. All door locks are now functioning and I'm happy. Just wished I could have solved the problem with a $4 motor, instead. Good luck to anyone attempting this repair and THANK YOU to everyone who has contributed to this thread.
#99
Driver School Candidate
Join Date: Apr 2010
Location: AZ
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the sticky! I have the auto door closers so it was a little different but who can complain about a 5 dollar fix? My mechanism is held back together with screws so I didn't reseal.
I've had to do this on my GS and daughters Celica too.
Still love Lexus.
Mike in AZ
I've had to do this on my GS and daughters Celica too.
Still love Lexus.
Mike in AZ
#100
Thanks for the sticky! I have the auto door closers so it was a little different but who can complain about a 5 dollar fix? My mechanism is held back together with screws so I didn't reseal.
I've had to do this on my GS and daughters Celica too.
Still love Lexus.
Mike in AZ
I've had to do this on my GS and daughters Celica too.
Still love Lexus.
Mike in AZ
#101
Driver School Candidate
Join Date: Apr 2010
Location: AZ
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Mike in AZ
#102
Driver School Candidate
Door stuck closed after attempting DIY
So I went ahead and bought the recommended motor off of ebay. After drilling out the older plastic gear so that the 'round shaft' would fit, I epoxied it together and made sure it spun. Then I reassembled everything as best as I could remember and made sure the wireless fob could activate the lock. It did, no problems there. But then after closing the door, I am unable to open it again (from the inside or outside). I get no resistance from the door handle.
I was able to remove the inside panel partially with the door closed and I can reach in and grab the gold rod. But even after moving it up and down, no luck. Also, pulling the lock/latch lines that connect to the interior handle/lock, does nothing.
Any advice for getting the door open? I think I can rework it once I get it open.
Thanks
I was able to remove the inside panel partially with the door closed and I can reach in and grab the gold rod. But even after moving it up and down, no luck. Also, pulling the lock/latch lines that connect to the interior handle/lock, does nothing.
Any advice for getting the door open? I think I can rework it once I get it open.
Thanks
#103
Ugh! Maybe someone with a slim jim can get the latch to release. Maybe not. The following is how I got into trouble and got out of it like you. The slim jim wouldn't work for me and I couldn't get my LX470 rear interior door panel off with the door closed.
I haven't (yet) performed the repair on my LS but I did my LX this past Winter. I hate to admit it but I put the latch mechanism back together wrong and shut the door as you did. In the case of the LX there was a little nylon piece that was temporarily removed and I put it back on the wrong way. Same problem: The latch wouldn't release either from inside or from the outside of the car. Big problem! I don't know why I didn't test the latch before shutting the door - brain fart - I guess. Next time be sure to test the latch using a screwdriver tip to close the latch and make sure that the inside and outside handles can release it (I guess that you know that by now )
Okay, this is what I did. I removed the interior panel that is just behind the door. This is on the inside of the "B" pillar. This where the seat belt rolls into. From there I used a Dremel tool and an air cutter to cut through the two nuts that hold the latch to the B pillar. It was not fun work but once done I just pushed the remaining screw stubs out of their holes and the door, with it's latch swung free. By inspecting the other side door I was able to see where a short length of coat hanger wire was able to release the latch from the door. I bought two new bolts and Nyloc nuts from the local hardware store and I was back in business for less than $5. Peeking into the B pillar should tell you what you're in for should you try something like this.
I haven't (yet) performed the repair on my LS but I did my LX this past Winter. I hate to admit it but I put the latch mechanism back together wrong and shut the door as you did. In the case of the LX there was a little nylon piece that was temporarily removed and I put it back on the wrong way. Same problem: The latch wouldn't release either from inside or from the outside of the car. Big problem! I don't know why I didn't test the latch before shutting the door - brain fart - I guess. Next time be sure to test the latch using a screwdriver tip to close the latch and make sure that the inside and outside handles can release it (I guess that you know that by now )
Okay, this is what I did. I removed the interior panel that is just behind the door. This is on the inside of the "B" pillar. This where the seat belt rolls into. From there I used a Dremel tool and an air cutter to cut through the two nuts that hold the latch to the B pillar. It was not fun work but once done I just pushed the remaining screw stubs out of their holes and the door, with it's latch swung free. By inspecting the other side door I was able to see where a short length of coat hanger wire was able to release the latch from the door. I bought two new bolts and Nyloc nuts from the local hardware store and I was back in business for less than $5. Peeking into the B pillar should tell you what you're in for should you try something like this.
#104
Driver School Candidate
Thanks for the input Bon. At first I was kind of confused by your directions... I was looking for those 'two bolts' everywhere. But I believe you're referring to the rear door, right?
Unfortunately, the front door can't be clipped like that.
I think my next order of business is going to be cutting through the striker bolt.
It's a U shape and screws into the body of the car. But if I can get a dremel in there... I might be in luck.
I'll let you all know how it goes.
Unfortunately, the front door can't be clipped like that.
I think my next order of business is going to be cutting through the striker bolt.
It's a U shape and screws into the body of the car. But if I can get a dremel in there... I might be in luck.
I'll let you all know how it goes.
#105
Did you remove the B pillar interior trim and look? I'm not saying that I know that you can access them from there but I'm curious if you looked and if there is an opening to see the striker nuts. The nuts are welded to a backing plate so they don't spin. The plate is tack welded to the sheet metal of the B pillar. I don't see how you can access the striker with the door closed because the door and B pillar block you.
I know my previous description was confusing. I was attempting to blend what I did to my BACK door on my LX and how you might approach your front door striker bolts/nuts through your B pillar.
I know my previous description was confusing. I was attempting to blend what I did to my BACK door on my LX and how you might approach your front door striker bolts/nuts through your B pillar.