Automatic transmission fluid replacement lx 570

RamonLx2013 · 2024-02-18 13:46:37

Lift the vehicle. [*1] Note Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1?). Remove the No. 2 engine under cover and oil pan protector assembly. Remove the drain plug and gasket, and drain the ATF. [*2] Temporarily install the gasket and drain plug. [*3] Tech Tips Reuse the old gasket. The plug will be removed again to adjust the fluid level Remove the refill plug and overflow plug. [*4] Add fluid to the refill hole until it flows out of the overflow plug hole. [*5] Note Use Toyota Genuine ATF WS. Wait until the fluid flow slows and only drops come out. [*6] Temporarily install the gasket and overflow plug. [*7] Tech Tips Reuse the old gasket. The plug will be removed again to adjust the fluid level. Add fluid to the refill hole using the amount of fluid specified for removal and installation of the oil pan. [*8] Tech Tips Specified amount of fluid is 2.1 liters (2.2 US qts, 1.9 Imp. qts). Temporarily install the gasket and refill plug to avoid fluid spillage. [*9] Tech Tips Reuse the old gasket. The plug will be removed again to adjust the fluid level. Lower the vehicle. [*10] Start the engine. [*11] Note Make sure that the A/C switch is off. Slowly move the shift lever from P to S and then back to P. [*12] Allow the engine to idle for 30 seconds to warm it up. [*13] Turn the engine switch off. [*14] Repeat steps [*1] to [*14]. Repeat steps [*1] to [*2]. Install a new gasket and the drain plug. Torque:20 N*m { 204 kgf*cm, 15 ft.*lbf } Repeat steps [*4] to [*10]. Adjust the fluid level Click here (http://zatonevkredit.ru/repair_manuals/raw_content/RM000002BL003WX.xml#RM000002BL003WX). Install the No. 2 engine under cover and oil pan protector assembly. Lower the vehicle. Operation complete.

Reply Subscribe

Thread Tools

Search this Thread

02-18-24 | 05:46 AM

RamonLx2013

Thread Starter

6th Gear

Joined: Aug 2023

Posts: 6

Likes: 0

From: Florida

Automatic transmission fluid replacement lx 570

Lift the vehicle. [*1]

Note

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).
Remove the No. 2 engine under cover and oil pan protector assembly.
Remove the drain plug and gasket, and drain the ATF. [*2]
Temporarily install the gasket and drain plug. [*3]

Tech Tips

Reuse the old gasket. The plug will be removed again to adjust the fluid level
Remove the refill plug and overflow plug. [*4]
Add fluid to the refill hole until it flows out of the overflow plug hole. [*5]

Note

Use Toyota Genuine ATF WS.
Wait until the fluid flow slows and only drops come out. [*6]
Temporarily install the gasket and overflow plug. [*7]

Tech Tips

Reuse the old gasket. The plug will be removed again to adjust the fluid level.
Add fluid to the refill hole using the amount of fluid specified for removal and installation of the oil pan. [*8]

Tech Tips

Specified amount of fluid is 2.1 liters (2.2 US qts, 1.9 Imp. qts).
Temporarily install the gasket and refill plug to avoid fluid spillage. [*9]

Tech Tips

Reuse the old gasket. The plug will be removed again to adjust the fluid level.
Lower the vehicle. [*10]
Start the engine. [*11]

Note

Make sure that the A/C switch is off.
Slowly move the shift lever from P to S and then back to P. [*12]
Allow the engine to idle for 30 seconds to warm it up. [*13]
Turn the engine switch off. [*14]
Repeat steps [*1] to [*14].
Repeat steps [*1] to [*2].
Install a new gasket and the drain plug.
Torque:20 N*m { 204 kgf*cm, 15 ft.*lbf }
Repeat steps [*4] to [*10].
Adjust the fluid level Click here.
Install the No. 2 engine under cover and oil pan protector assembly.
Lower the vehicle.
Operation complete.