Member Help thread from a Lexus Certified Technician
#826
Thank you for the response, I don't currently have the VSS speed sensor wire hooked up, never have. Unless you mean to unplug everything else? I had left it disconnected and everything was fine, but when hooking up the SWIPS i misread purple for pink, and thus I hooked up the SWIPS to the speed sensor wire. I have checked the fuses (both under dash and under the hood).... However, Is there one in particular that it would be... I can definitely double check it. Is it possible that by hooking up the VSS wire to the head unit, it could resolve this issue? Currently I just have the wire capped off and not hooked up to anything at all.
Is there anything in particular that I could take pictures of?
Is there anything in particular that I could take pictures of?
#827
Drive the car while turning the wheel left and right to determine which side the noise is coming from; while turning you will hear a grinding, rubbing type noise. If its coming from the front I would replace both fronts since one goes bad the other one wouldn't be far off.
#828
Normally these systems are interlinked so if you get a check engine light or vsc light it disables the cruise control for safety.
#829
oil change
spark plugs
plug wires
timing belt
water pump
thermostat
cam seals
front main seal
serpentine belt
t-belt tensioner
idler pulleys
trans flush ( depends on fluid color (( dark do not change, reddish change )) )
rear diff fluid ( gear oil 75w90 gl5)
coolant flush
#830
Hey how are you, I just had my crank pulley and the O ring on my distributor fixed yesterday, drove the car all day and it was fine. Today when i tried to crank it would'nt start. I changed the battery and checked my ground, but that wasnt the problem. I've never had any problem at all with my starter before so I really dont know else it could be. Got any other ideas?
#832
CEL Code 13
Hi tach Man:
Thank you for what you do for this community.
Have a 93 100LS with about 160K on it. recently did the deal with the tiing belt, rollers, tensionsioner, WP, everything.
Everything works well for about 5K. Then my CEL came on last week went off a couple of times. I took it to a local service place. They said it was a Code 13 .. Crankshaft Position sensor, according to the service people.
They replaced it, and pronounced it ok. I went to pick it up, started it...no light, and then the light comes back on.
they are telling me its throwing a hard code ...13 again ..and point towards the ECU ....
Everything I read tells me this is the camshaft position sensor ... and they are wrong ...
I cannot afford to have them go on a search and destroy mission until they somehow fix it through blind luck ..
any thoughts or guidance ...
thanks
radiohound
Thank you for what you do for this community.
Have a 93 100LS with about 160K on it. recently did the deal with the tiing belt, rollers, tensionsioner, WP, everything.
Everything works well for about 5K. Then my CEL came on last week went off a couple of times. I took it to a local service place. They said it was a Code 13 .. Crankshaft Position sensor, according to the service people.
They replaced it, and pronounced it ok. I went to pick it up, started it...no light, and then the light comes back on.
they are telling me its throwing a hard code ...13 again ..and point towards the ECU ....
Everything I read tells me this is the camshaft position sensor ... and they are wrong ...
I cannot afford to have them go on a search and destroy mission until they somehow fix it through blind luck ..
any thoughts or guidance ...
thanks
radiohound
Last edited by radiohound; 01-30-11 at 09:55 PM. Reason: more info provuded.
#833
Hi Tach Motor
I have a 2002 LS 430 with right at 70k. I am the second owner, purchased from a Lexus dealership. My problem: the low oil pressure dash light came on. I had it towed the the dealer where I purchased it, and after several days they called and said it has a sludge problem. To the point of having to replace rings. And suggestions here? They said that although I have changed the oil religiously and had the 60k checkup, that probably the previous owner may have never changed the oil. Which, I find difficult to understand.
Anyway, they said they were going to ask Toyoto for financial help for the repair. And that I might need to call them. I asked what the fee is, for changing the rings, and they said $5,000 for just that.
Do you have any advice for me? Specific questions I should be asking? Anything else I should be doing to keep the fix from being too expensive?
Thanks very much.
I have a 2002 LS 430 with right at 70k. I am the second owner, purchased from a Lexus dealership. My problem: the low oil pressure dash light came on. I had it towed the the dealer where I purchased it, and after several days they called and said it has a sludge problem. To the point of having to replace rings. And suggestions here? They said that although I have changed the oil religiously and had the 60k checkup, that probably the previous owner may have never changed the oil. Which, I find difficult to understand.
Anyway, they said they were going to ask Toyoto for financial help for the repair. And that I might need to call them. I asked what the fee is, for changing the rings, and they said $5,000 for just that.
Do you have any advice for me? Specific questions I should be asking? Anything else I should be doing to keep the fix from being too expensive?
Thanks very much.
Secondly, I found a former Lexus mechanic that has his own shop in my area. He worked at Lexus for 15 years. He is far better than going to Lexus not just for the labor rate (about 50%) but the fact that he will use aftermarket parts AND he will attempt to fix something before he replaces it. For example my steering column motors were acting up. I took it to Lexus and they told me in no uncertain terms that I needed to replace both motors on my LS430 steering column ($900 for just parts). I took it to the former Lexus employee- he told me that Lexus actually had these problems frequently and they developed a special grease just for the steering column. He applied the grease 3 weeks ago and the problem was solved! Try to google "toyota or lexus mechanic" in your area. I'm sure there is one nearby. Anything Lexus tells you, divide it by 2 and then 2 again and thats what it should cost with a regular mechanic.
#835
#836
Hey how are you, I just had my crank pulley and the O ring on my distributor fixed yesterday, drove the car all day and it was fine. Today when i tried to crank it would'nt start. I changed the battery and checked my ground, but that wasnt the problem. I've never had any problem at all with my starter before so I really dont know else it could be. Got any other ideas?
#837
#838
Hi tach Man:
Thank you for what you do for this community.
Have a 93 100LS with about 160K on it. recently did the deal with the tiing belt, rollers, tensionsioner, WP, everything.
Everything works well for about 5K. Then my CEL came on last week went off a couple of times. I took it to a local service place. They said it was a Code 13 .. Crankshaft Position sensor, according to the service people.
They replaced it, and pronounced it ok. I went to pick it up, started it...no light, and then the light comes back on.
they are telling me its throwing a hard code ...13 again ..and point towards the ECU ....
Everything I read tells me this is the camshaft position sensor ... and they are wrong ...
I cannot afford to have them go on a search and destroy mission until they somehow fix it through blind luck ..
any thoughts or guidance ...
thanks
radiohound
Thank you for what you do for this community.
Have a 93 100LS with about 160K on it. recently did the deal with the tiing belt, rollers, tensionsioner, WP, everything.
Everything works well for about 5K. Then my CEL came on last week went off a couple of times. I took it to a local service place. They said it was a Code 13 .. Crankshaft Position sensor, according to the service people.
They replaced it, and pronounced it ok. I went to pick it up, started it...no light, and then the light comes back on.
they are telling me its throwing a hard code ...13 again ..and point towards the ECU ....
Everything I read tells me this is the camshaft position sensor ... and they are wrong ...
I cannot afford to have them go on a search and destroy mission until they somehow fix it through blind luck ..
any thoughts or guidance ...
thanks
radiohound
#840
I have a ls460, 2008. I had a clicking noise when pushing on the brakes. Lexus replaced the brake accuator about a year ago. Noise was gone, but recently returned as a click, click, click when I brake at slow speeds. I took it to Lexus yesterday for the VSR recall, and was told they could not hear the brake clicking noise. I am going to test drive it tomorrow when I pick it up at the dealer. Is there still a problem with the accuator?