Lexus nx oil change concern - does this oil look new or old?
#31
Intermediate
Unfortunately, sometimes we have to learn things the HARD way. I'm of the opinion that if you do learn something the HARD way, it will be more ingrained in your head and you're more apt to remember it.
For many, many years of being a DIYer, I've paid attention to some of the things that have torque specs, but not all. Well, a few months ago I learned my lesson and now I'm more apt to think twice about tightening something (such as spark plugs). I had a horrible situation recently where I tightened my oil filter canister on my 2020 Lexus NX - TOO tight. When it came time to remove it, it was a struggle and I broke a hold in it. I didn't even realize I broke the canister until I started the engine! Good thing I never ran the engine more than 10 seconds until I realized what had happened. Well, then I went back to researching this situation and, after glancing at about 10 postings/videos I finally found someone who suggested TORQUING it to spec! Who would've thought? All these years I've always just tightened my oil filters/canisters without torquing. When it came time to replace that canister, I really wanted the OEM (which is hard plastic). But 3rd parties offer these METAL ones, which you would think would be better! I'm pretty much an OEM guy. So I decided to order an OEM canister AND torque it when I replace the filter. That's what I do now! Surprise - when you torque it, it doesn't even seem like it's tight enough - but it is! Haven't had the problem again, and expect I never will.
When it came time to do my plugs, I decided I'll be a good boy and torque them. NEVER in my life have I ever torqued plugs! I'm a changed man now. I have my large torque wrench (ft pounds) and my smaller one (inch pounds).
Some might say (especially after reading this post) that I'm quite a talker. Well, I'm not only quite a talker, but I'm also now quite a TORQUER
For many, many years of being a DIYer, I've paid attention to some of the things that have torque specs, but not all. Well, a few months ago I learned my lesson and now I'm more apt to think twice about tightening something (such as spark plugs). I had a horrible situation recently where I tightened my oil filter canister on my 2020 Lexus NX - TOO tight. When it came time to remove it, it was a struggle and I broke a hold in it. I didn't even realize I broke the canister until I started the engine! Good thing I never ran the engine more than 10 seconds until I realized what had happened. Well, then I went back to researching this situation and, after glancing at about 10 postings/videos I finally found someone who suggested TORQUING it to spec! Who would've thought? All these years I've always just tightened my oil filters/canisters without torquing. When it came time to replace that canister, I really wanted the OEM (which is hard plastic). But 3rd parties offer these METAL ones, which you would think would be better! I'm pretty much an OEM guy. So I decided to order an OEM canister AND torque it when I replace the filter. That's what I do now! Surprise - when you torque it, it doesn't even seem like it's tight enough - but it is! Haven't had the problem again, and expect I never will.
When it came time to do my plugs, I decided I'll be a good boy and torque them. NEVER in my life have I ever torqued plugs! I'm a changed man now. I have my large torque wrench (ft pounds) and my smaller one (inch pounds).
Some might say (especially after reading this post) that I'm quite a talker. Well, I'm not only quite a talker, but I'm also now quite a TORQUER
#33
Unfortunately, sometimes we have to learn things the HARD way. I'm of the opinion that if you do learn something the HARD way, it will be more ingrained in your head and you're more apt to remember it.
For many, many years of being a DIYer, I've paid attention to some of the things that have torque specs, but not all. Well, a few months ago I learned my lesson and now I'm more apt to think twice about tightening something (such as spark plugs). I had a horrible situation recently where I tightened my oil filter canister on my 2020 Lexus NX - TOO tight. When it came time to remove it, it was a struggle and I broke a hold in it. I didn't even realize I broke the canister until I started the engine! Good thing I never ran the engine more than 10 seconds until I realized what had happened. Well, then I went back to researching this situation and, after glancing at about 10 postings/videos I finally found someone who suggested TORQUING it to spec! Who would've thought? All these years I've always just tightened my oil filters/canisters without torquing. When it came time to replace that canister, I really wanted the OEM (which is hard plastic). But 3rd parties offer these METAL ones, which you would think would be better! I'm pretty much an OEM guy. So I decided to order an OEM canister AND torque it when I replace the filter. That's what I do now! Surprise - when you torque it, it doesn't even seem like it's tight enough - but it is! Haven't had the problem again, and expect I never will.
When it came time to do my plugs, I decided I'll be a good boy and torque them. NEVER in my life have I ever torqued plugs! I'm a changed man now. I have my large torque wrench (ft pounds) and my smaller one (inch pounds).
Some might say (especially after reading this post) that I'm quite a talker. Well, I'm not only quite a talker, but I'm also now quite a TORQUER
For many, many years of being a DIYer, I've paid attention to some of the things that have torque specs, but not all. Well, a few months ago I learned my lesson and now I'm more apt to think twice about tightening something (such as spark plugs). I had a horrible situation recently where I tightened my oil filter canister on my 2020 Lexus NX - TOO tight. When it came time to remove it, it was a struggle and I broke a hold in it. I didn't even realize I broke the canister until I started the engine! Good thing I never ran the engine more than 10 seconds until I realized what had happened. Well, then I went back to researching this situation and, after glancing at about 10 postings/videos I finally found someone who suggested TORQUING it to spec! Who would've thought? All these years I've always just tightened my oil filters/canisters without torquing. When it came time to replace that canister, I really wanted the OEM (which is hard plastic). But 3rd parties offer these METAL ones, which you would think would be better! I'm pretty much an OEM guy. So I decided to order an OEM canister AND torque it when I replace the filter. That's what I do now! Surprise - when you torque it, it doesn't even seem like it's tight enough - but it is! Haven't had the problem again, and expect I never will.
When it came time to do my plugs, I decided I'll be a good boy and torque them. NEVER in my life have I ever torqued plugs! I'm a changed man now. I have my large torque wrench (ft pounds) and my smaller one (inch pounds).
Some might say (especially after reading this post) that I'm quite a talker. Well, I'm not only quite a talker, but I'm also now quite a TORQUER
Thread
Thread Starter
Forum
Replies
Last Post
AMIRZA786
IS - 2nd Gen (2006-2013)
13
05-17-22 02:11 PM