quikturbo

Ok, time for alittle update.

This past saturday we held a Chi2k4 Supra event at SP in Illinois. The turn out was awesome!!! Saturday was the dyno day, and Sunday the track day. Even though it did rain a bit on Saturday, there was a massive crowd. I decided to throw my car on the dyno to turn up the boost from last time. So here are the results

@30psi
698rwhp
640rwtq

The car is running a bit rich, and timing is pretty conservative, so I know I can hit 700+rwhp on these stock cams

On another note:
We went to do a 1/4 mile pull on the dyno, and while shifting into 2nd, we snapped the driveshaft I knew that thing wasn't going to last too long. Better that to give then the 6spd or the diff. This was a custom supra tt driveshaft that Toyomoto lengthened for me, unfortunately they didn't lenghten it enough, so only a small part of the rear half shaft section, inserted into the front half shaft. So I basically just stripped all thos splines right off. Here is a picture of the aftermath.


Should be ready tomorrow with a 1 piece custom drive shaft made by SP.

Pics and videos will be posted soon

Chris

siniquezu

Did you get the methanol kit in yet?

quikturbo

It's in, but I haven't connected the line yet. My passes were on 110 octane. I'm still having some issues with the pump going on at the wrong times, not sure what's up though. I'll figure out the bugs soon.

siniquezu

So the toyo driveshaft wasn't under warranty?

quikturbo

Not that I know of. seeing as they are fabricating and cutting a driveshaft, I don't know that many people would stand behind that.
I may try to make a call, we'll have to see.

DIrEctQL

That was an entertaining day.

I think Overclocker (Wolf) got it on tape. It was some crazy stuff. Nice work on the car Chris.

Too bad you didn't stick around for my car on a dyno. By far the most quiet car there.

Chris

LsportGS4

thats vurry nice

quikturbo

Here is a pic someone snapped as my car was going onto the dyno. I love that pic



As for the drive shaft, SP has created a gorgeous 1 piece custom unit. self centering CNC'd aluminum flanges, 3" steel shaft and heady duty U-joints. This is basically the same shaft they have on there 9.0 sec drag car It should handle pretty much everthing I throw at it, including 2 step launches!! This new one feels solid, no vibration at all.

Here are a couple pics of the flanges.




I talked to Wolf and he should have some stuff hosted soon. Sorry about having to miss your maiden run with your swapped SC. I'll see it again soon.


Chris

TurboB6

Looks exactly like my PHR setup Chris, lol

Get some track times already

Richie

Thanks for the new WP!!

TurboSC

Yeah that was a fun day, to bad I had to leave early! Me any my buddy are going to be editing the video we took of the dyno runs, and the driveshaft mishap! This car is AMAZING in person. Pictures do not do it justice AT ALL.

Lex Luthor

Nice 'shaft....Gary called me and told me you blew that thing, looks like you've got a permanent solution.
Here's another pic of Chris' whip...

Did ya see mine C.T.?

quikturbo

Hey now big boy, gettin a bit personal aren't we LOL jk
Permanent solution is an understatement

Jon, I've been watching over your car since it arrived.. They're taking good care of it, and hopefully it will be back in your driveway soon enough.

Thanks for the compliments Tony, I can't wait for those vids!!!!

Chris

lexcoupe

i wish my car was ready by then... then i could have laid down some numbers too.. but too bad it wasnt... next meet it will be there hopefully.

Kevin

HotBoy

WOW !!