1992 sc300 1jz & r154 swap
05-30-08, 08:27 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
i am still wait on parts.....driftmotion said walbro and the sc pedal conversion kits are on back order sooooo..
05-30-08, 08:29 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
i also bought some rubber power steering lines so i dont have to move the battery to the trunk.
05-30-08, 08:29 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
here are thos power steering lines. i am going to run the intercooler piping right in front of the a/c hard lines.
05-31-08, 03:45 AM
Driver School Candidate
Join Date: May 2008
Location: CA
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
what are you gonna do about the wiring harness...have it figured out yet? I believe it should just plug in soarer to sc300...
05-31-08, 09:53 AM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
it will plug in if i extend the harness.....
05-31-08, 02:21 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
sorry... tell me i am dumb, it is a r154. i thought i had 7 gears......well anyways i am leaking oil from the back of my valve cover. do you think it is my cam seal?
05-31-08, 02:22 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
here is another shot
05-31-08, 02:24 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
this soarer clip was a automatic it still has its auto ecu and harness
Last edited by gdc5ind; 06-05-08 at 05:24 PM .
05-31-08, 05:56 PM
Driver School Candidate
Join Date: May 2008
Location: CA
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
try cleaning the crap out of it using parts cleaner spray, and im sure once you put on a valve cover gasket and or cam seal gasket you can call it a day...
05-31-08, 08:20 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
just started the wiring harness.... does anyone have any advice or tips?
06-01-08, 10:11 AM
Driver School Candidate
Join Date: May 2008
Location: CA
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
heres what i found somewhere while researching how to do the wiring..was told this was the right way...
Attached Thumbnails
06-01-08, 10:28 AM
Racer
Join Date: Jun 2007
Location: Washington
Posts: 1,598
Thats not the right way. The ECU will not bolt up in the stock location. Both need to be extended.
06-01-08, 03:05 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
well it looks like all the connectors are going to need to be extended 20"(to be safe) what do you guys think about this soldering work? or would you guys just go with connectors?
Last edited by gdc5ind; 06-01-08 at 03:10 PM .
06-01-08, 03:08 PM
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
so i need to extend the
red connectors at the
green part i circled?
06-01-08, 06:08 PM
Driver School Candidate
Join Date: May 2008
Location: CA
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
yeesh thats alot of wires im assuming yes ...what harm would it be to extend from that location ...solder,heatshrink, repeat...