1992 sc300 1jz & r154 swap
06-01-08, 06:55 PM
#61
Racer
Those solder connections will be better than crimps.
06-01-08, 08:28 PM
#64
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
i found a 1jz-gte gasket set from http://store.driftmotion.com/Static/...egasketset.php
165$
I dont want to cut my transmission tunnel for the shifter to come through(or the 2.25inch from where it used to be). where can i buy a r154 ball hinge so i can cut and extend it?http://www.clubna-t.com/forums/showthread.php?t=744
165$
I dont want to cut my transmission tunnel for the shifter to come through(or the 2.25inch from where it used to be). where can i buy a r154 ball hinge so i can cut and extend it?http://www.clubna-t.com/forums/showthread.php?t=744
Last edited by gdc5ind; 06-01-08 at 09:01 PM.
06-02-08, 05:37 PM
#66
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
i called carson toyota today to see if i could order some parts from toyota japan, i need the shifter housing(part#33521-24040) and shifter control lever(part#33570-24010). well he said he would call me back after he gets an email back with pricing from toyota japan. he calls me back in like 25mins and says that they dicontinued one of the parts but he doesnt know which one.my question is. does anyone know what the part number is on a r154 shifter housing and shift control lever? other then that i still need to.....
1.extend the harness(i am half done)
2.mod stock exhaust(should i cut out the cat and resonators??)
3.cut tunnel or buy supra(dont know what year???) shifter housing to cut and extend.
4.pedal conversion(waiting for kit)
5.gaskets (really should replace a few gasket)
6.drive shaft
also how would you guys go about finishing this swap??
1.extend the harness(i am half done)
2.mod stock exhaust(should i cut out the cat and resonators??)
3.cut tunnel or buy supra(dont know what year???) shifter housing to cut and extend.
4.pedal conversion(waiting for kit)
5.gaskets (really should replace a few gasket)
6.drive shaft
also how would you guys go about finishing this swap??
Last edited by gdc5ind; 06-02-08 at 05:42 PM.
06-06-08, 06:48 PM
#73
Pole Position
Thread Starter
Join Date: Jul 2007
Location: CA
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
i picked you the sc300 OEM manual pedal kit 270$ it came with brake & clutch pedal and the mounting bracket assembly. also picked up a walbro fuel pump 98$.the only thing holding me back is two small leaks coming from valve covers and front main seal or oil pan(havent taken on timing belt cover) i am think of just droping it in and when the gasket set comes in pull the radiator out and do it with the engine in the car.
06-06-08, 08:59 PM
#74
Driver School Candidate
Join Date: May 2008
Location: CA
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
man looking good...you need to show me how to polish my stuff when I get back.. my engines are leaving japan this week on the 10th enroute to long beach yea baby! anyways interested in an HKS twin plate? Brand new? hmm keep up the good work.. i would install it in the car and fix it afterwards...but id want to know exactly where its comming from first...
