help with auto tt wiring
#16
Lexus Champion
iTrader: (12)
Oh, and IK1 pin 22 is related to the OD circuit. I dont know the full functionality of that circuit, so I cant say whether putting the car in L should energize it or not. I would start by verifying all the pins and colors between the gear indicator and IK1 are correct.
I am referencing Supra and Lexus wiring to verify colors vs pinouts, so bear with me and I will try to get you a full breakdown on the IK1 pins.
I am referencing Supra and Lexus wiring to verify colors vs pinouts, so bear with me and I will try to get you a full breakdown on the IK1 pins.
#19
Lexus Champion
Thread Starter
iTrader: (13)
Join Date: Feb 2008
Location: Sacramento
Posts: 2,187
Likes: 0
Received 0 Likes
on
0 Posts
pin 14 is dark green with gray marks. pin 16 is lime green with yellow. Weird thing is that pin 14 get the 12v when in D but its connected to pin 9 on ecu plug. Didnt you tell me that 2 is suppose to be connected to that? By the way the two pins were reversed before i made the correction.
#20
Lexus Champion
Thread Starter
iTrader: (13)
Join Date: Feb 2008
Location: Sacramento
Posts: 2,187
Likes: 0
Received 0 Likes
on
0 Posts
this is the only diagram ive been able to find of the nsw
http://personal.utulsa.edu/~nathan-b...23parkneut.pdf
When i put the gear selector on 2 i get no voltage from pin 16. Pin 14 has 12v when its in D but its spliced into pin 9 of the e10 connector. Pin 9 is 2 not D.
http://personal.utulsa.edu/~nathan-b...23parkneut.pdf
When i put the gear selector on 2 i get no voltage from pin 16. Pin 14 has 12v when its in D but its spliced into pin 9 of the e10 connector. Pin 9 is 2 not D.
Last edited by soarer13oy; 10-06-10 at 12:11 PM.
#22
Lexus Champion
Thread Starter
iTrader: (13)
Join Date: Feb 2008
Location: Sacramento
Posts: 2,187
Likes: 0
Received 0 Likes
on
0 Posts
Ok so i spliced the wire from pin 9 to pin 16 on ik1 and indicator light works fine now only thing is 2 doesnt light up because its not getting 12v when i put it in 2. Im not worried about that i just want it to drive right. Ima take it for a spin and report back.
#27
Lexus Champion
Thread Starter
iTrader: (13)
Join Date: Feb 2008
Location: Sacramento
Posts: 2,187
Likes: 0
Received 0 Likes
on
0 Posts
Mines was the same that how i burnt it. Cant wait for the one aligas sending me. I also have some ls400 calipers on the way, my damn boost problem is killing me though. If i go wot right away it will only boost 3-5 psi, but if i let it build boost i can boost 15psi no prob. Ive been working on this for a while without any results.
Last edited by soarer13oy; 10-06-10 at 07:10 PM.
#29
Lexus Champion
Thread Starter
iTrader: (13)
Join Date: Feb 2008
Location: Sacramento
Posts: 2,187
Likes: 0
Received 0 Likes
on
0 Posts
Thats what im going to do tomorrow. Ive replaced so many crap on it to try to get it to work. If i only had the money to go single lol. So you had to tap the ingnitor wire to get your tach to work?
Last edited by soarer13oy; 10-06-10 at 07:25 PM.
#30
Lexus Champion
iTrader: (12)
Well, I tapped the igniter wire and it still wouldn't work. I was pissed! I eventually figured out that I had accidentally fed the tach out pin of the igniter with 12v My mistake! Anyhow, once I cut the voltage to that pin on the igniter, the tach started working. Long story short, mine was a self inflicted wiring issue. Yours may just work if you tap the igniter wire. Its the small black wire on pin 1 of the 4 pin igniter plug.