aristo wiring experts needed
#16
Next problem. Connectors on steerong rack
These are the two connectors that are connected to the rack pinion. The wires were not connected to anything. There are a total of 4 wires between the two connectors. Grey connector has light green w/ black stripe, and light green w/ red stripe. The Black connector has light green w/ red stripe and brown w/ grey dot.
#17
EB1 Pin 7 has a wire that goes to pin 1 on the AC clutch. Then a wire branches off of that wire and connects to pin 1 another AC related connector called II1.
Grey connector:
The LG-R goes to IJ2 pin 16
The LG-B goes to IJ2 pin 6
Black connector:
AFAIK is not used on an Aristo swap.
You can try:
LG-R wire to the small ecu plug on pin 35
Brown wire to IK1 pin 1 or directly to one of the engine ground pigtails on the intake manifold.
Pics of IJ2 and IK1 attached for reference.
These are the two connectors that are connected to the rack pinion. The wires were not connected to anything. There are a total of 4 wires between the two connectors. Grey connector has light green w/ black stripe, and light green w/ red stripe. The Black connector has light green w/ red stripe and brown w/ grey dot.
Grey connector:
The LG-R goes to IJ2 pin 16
The LG-B goes to IJ2 pin 6
Black connector:
AFAIK is not used on an Aristo swap.
You can try:
LG-R wire to the small ecu plug on pin 35
Brown wire to IK1 pin 1 or directly to one of the engine ground pigtails on the intake manifold.
Pics of IJ2 and IK1 attached for reference.
#18
EB1 pin 4 (Black/Yellow)goes from 30 amp EFI fuse to small ecu connector, pin 33 BATT.
EB1 pin 8 (Black/Orange)goes from EFI main relay to small ecu connector pin 24 M-RELAY.
EB1 pin 6 (Black/Red) goes from ABS relay pin 5 to data link check connector pin 23
EB1 pin 1 (Lavender) goes from ac clutch relay pin 3 to ac clutch pin 4
EB1 pin 2 (White) goes from ac clutch relay to small ecu connector pin 23 ACMG
EB1 pin 7 (Brown) goes from ac temp sensor to Il1 pin 1 and ac clutch pin 1
EB1 Pin 3 (Black) goes from starter relay pin 1 to various places depending on if the car is auto or manual. Let me know if you need more info on that one...
I think that is it.
EB1 pin 8 (Black/Orange)goes from EFI main relay to small ecu connector pin 24 M-RELAY.
EB1 pin 6 (Black/Red) goes from ABS relay pin 5 to data link check connector pin 23
EB1 pin 1 (Lavender) goes from ac clutch relay pin 3 to ac clutch pin 4
EB1 pin 2 (White) goes from ac clutch relay to small ecu connector pin 23 ACMG
EB1 pin 7 (Brown) goes from ac temp sensor to Il1 pin 1 and ac clutch pin 1
EB1 Pin 3 (Black) goes from starter relay pin 1 to various places depending on if the car is auto or manual. Let me know if you need more info on that one...
I think that is it.
What is pin 6 suppose to be connected too.
Last edited by pourSc; 06-29-11 at 05:26 AM.
#19
EB1 Pin 7 has a wire that goes to pin 1 on the AC clutch. Then a wire branches off of that wire and connects to pin 1 another AC related connector called II1.
Grey connector:
The LG-R goes to IJ2 pin 16
The LG-B goes to IJ2 pin 6
Black connector:
AFAIK is not used on an Aristo swap.
You can try:
LG-R wire to the small ecu plug on pin 35
Brown wire to IK1 pin 1 or directly to one of the engine ground pigtails on the intake manifold.
Pics of IJ2 and IK1 attached for reference.
Grey connector:
The LG-R goes to IJ2 pin 16
The LG-B goes to IJ2 pin 6
Black connector:
AFAIK is not used on an Aristo swap.
You can try:
LG-R wire to the small ecu plug on pin 35
Brown wire to IK1 pin 1 or directly to one of the engine ground pigtails on the intake manifold.
Pics of IJ2 and IK1 attached for reference.
#21
#22
On Eb1 connector, pin 3 is the blk wire, pin 5 is the blue w/ red stripe. The blue w/ red stripe is not going through the harness at all. However, the the blk wire is connected to blue w/ red stripe in the harness. Not at the connector at all. When I traced the wire, it is connected to pin number 6 (blk w/ white stripe) on the grey connector (14 pins).
#24
#25
They tied EB1 pin 3 to IJ1 pin 6 to bypass the Neutral start switch. That is fine to leave like it is so the car will start. So they just used a blue/red wire to tie between the two, or does the splice effectively tie EB1 pins 3 and 5 together?
#26
They used a blue w/red wire to between the two wires. So, I gues I should leave this the way that it is. What the actual blue with red wire? Do I need to hook it up?
#30
I can see the light at the end of this tunnel.
There are a few wires that are left over. The are some that I know should be there, and they aren't. These are mainly on body plugs. So, I hope that you guys are still on board.
First, on the Grey connector (14pin), The two Org/ w blk stripe wires are not connected to anything. Should connect these to other Org w/ blk wires?
On the same connector, Pin 2 (red w/blue stripe) isn't connected. Pin 14 (white w/blk stripe), isnt connected. I know that pin 2 is supposed to be connected, I dont know where.
The Orange connector (23 Pins), Pin 6 (red wire) and pin 7 (blue w/red wire) are not connected. In the notes that I have, they show both connected to light blue wires. I did find two wires, but I wasnt able to trace them.
On the smller grey connector (17 pins), pin 13 (blk w/yellow) isnt connected. Where should I connect this wire? To another blk w/yellow wire?
On the White connector (12 pins), pin 2 (Red w/ blue stripe) is connected to pin 7 (blk w/yellow). How should these be correctly hooked up?
Last, on the white connector (25 pins), there are only 2 wires pin 9 and 24. are there suppose to be any other wires on this connector? My notes show pin 2 and 25 should be connected.
First, on the Grey connector (14pin), The two Org/ w blk stripe wires are not connected to anything. Should connect these to other Org w/ blk wires?
On the same connector, Pin 2 (red w/blue stripe) isn't connected. Pin 14 (white w/blk stripe), isnt connected. I know that pin 2 is supposed to be connected, I dont know where.
The Orange connector (23 Pins), Pin 6 (red wire) and pin 7 (blue w/red wire) are not connected. In the notes that I have, they show both connected to light blue wires. I did find two wires, but I wasnt able to trace them.
On the smller grey connector (17 pins), pin 13 (blk w/yellow) isnt connected. Where should I connect this wire? To another blk w/yellow wire?
On the White connector (12 pins), pin 2 (Red w/ blue stripe) is connected to pin 7 (blk w/yellow). How should these be correctly hooked up?
Last, on the white connector (25 pins), there are only 2 wires pin 9 and 24. are there suppose to be any other wires on this connector? My notes show pin 2 and 25 should be connected.