When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
several 1.02 updates have been sent out, please send us feedback via our zendesk so we can push out further updates.
If you haven't received 1.02 yet you will this week. Only a few IDs left
Last edited by OrangeVirus Tuning; 09-17-19 at 08:22 AM.
several 1.02 updates have been sent out, please send us feedback via our zendesk so we can push out further updates.
If you haven't received 1.02 yet you will this week. Only a few IDs left
Will customizations such as higher rev limit and adjustments for charge pipes carry over or will we have to send logs again? Thanks
For those of you that already received the 1.02 file, do you notice any differences? Just wanna know what to expect while I wait to get the file
Still to early to give a full review as it was just flashed this morning. From what I understand, most newer ECUs have a learning period after being flashed. But for now, I feel like there is slightly less torque if I floor it from a standstill (not necessarily a bad thing). With the 1.01 file and traction control turned off, smashing the throttle would result in tire spin for a second or so.
Once 3500 rpm was reached, torque comes on pretty strong. It was a fun drive to work. Top end feels the same, probably due to the anemic turbo. I can only hope things get better as the learning period makes its necessary corrections and as fall and winter bring more desirable air temperatures.
Still to early to give a full review as it was just flashed this morning. From what I understand, most newer ECUs have a learning period after being flashed. But for now, I feel like there is slightly less torque if I floor it from a standstill (not necessarily a bad thing). With the 1.01 file and traction control turned off, smashing the throttle would result in tire spin for a second or so.
Once 3500 rpm was reached, torque comes on pretty strong. It was a fun drive to work. Top end feels the same, probably due to the anemic turbo. I can only hope things get better as the learning period makes its necessary corrections and as fall and winter bring more desirable air temperatures.
How about drive modes? I wonder what the 1.02 update covered...
How about drive modes? I wonder what the 1.02 update covered...
Didn’t mess with driving modes. Assuming Sport is the most aggressive, I only use that mode and try to hit every load point for about 200 miles while it’s learning. After that I’ll explore the other modes.
For details on what the update covers, Matt explains what tables are changed/enhanced in some of his previous posts. Check about 3 or 4 pages back.
Didn’t mess with driving modes. Assuming Sport is the most aggressive, I only use that mode and try to hit every load point for about 200 miles while it’s learning. After that I’ll explore the other modes.
For details on what the update covers, Matt explains what tables are changed/enhanced in some of his previous posts. Check about 3 or 4 pages back.
Ah, found it. Please do keep us posted on the changes that you discover. I have yet to receive the update for my 78132 NX.
Originally Posted by OrangeVirus Tuning
Our 1.02 ECU / TCU Tune update will include :
Updated boost strategy :
- Single boost table from 1.01 code will be modified to a 3D boost reference table that has pressure vs load (example of what stock is (the small table below) and our version)
Updated Fuel enrichment cross-over:
This will modify when the ECU allows for fuel enrichment based on throttle position and accelerator position so that fuel enrichment can come on sooner than 4500+ rpm / full throttle.
Modified Torque control logic:
A modified version of our current torque control logic tables, increases response and shift control.
Condensed fuel compensation tables:
Rather than having 2 different compensation tables for fuel / maf load, we condense this into a single target table.
more information will be given as we get closer to release.
19 Customer files are being updated tomorrow and sent out including yours. Right now zendesk is our best way, we have just been a bit behind. We are expanding and adding 2 new people to the team when we do so that the future will be much faster.
This file is available, send us a ticket requesting it since I'm not sure who you are sorry
I've been sending tickets for 78132 G-C 002 but haven't received any reply. Is there an ETA for this? Will adjustments for the charge pipe be carried over or would I need to log again?
If 1.02 for the 78132 NX is too difficult to do then please send the corrected modes map for 1.01G-C 002. You mentioned having gotten to the bottom of this weeks ago:
Originally Posted by OrangeVirus Tuning
Hello,
We have an update that we are working on for the NX200T that we want everyone to be aware of. One person with the tune pointed it out. The mode settings for the NX200T (eco,normal,sport) are setup differently than the IS200T, in this case the tune will make the modes backwards (eco = fastest). For the NX200 ECUs we will have an updated version that corrects this.
Is 53Q22 available yet?
I sent a datalog Aug 19th too with no response.
This file was already sent to you a few days ago
Originally Posted by chezgk
I've been sending tickets for 78132 G-C 002 but haven't received any reply. Is there an ETA for this? Will adjustments for the charge pipe be carried over or would I need to log again?
If 1.02 for the 78132 NX is too difficult to do then please send the corrected modes map for 1.01G-C 002. You mentioned having gotten to the bottom of this weeks ago:
I am almost finished with 78132. It's not that it it is too difficult or not, it's just finding all the map code takes time.
To give everyone a clear idea here, from when we initially started we had about 5 ECU versions to support. Right now we have 30+ ECU versions, and it is growing. For new or potential customers.. please be aware 2019 ECUs require the most time right now. And also RC200T ecus, as they have additional modes.
Originally Posted by chezgk
Ah, found it. Please do keep us posted on the changes that you discover. I have yet to receive the update for my 78132 NX.
This needs to be updated further as we have also completely retuned airload control tables as well
If there is anyone who has NOT received 1.02 update please send us a ticket/email (support@ovtune.zendesk.com)
include:
Name
system ID
ECU ID
requesting 1.02
Future updates after this will be available through flash manager so it won't need requested
Last edited by OrangeVirus Tuning; 09-21-19 at 06:28 AM.
09-17-19, 06:26 AM
