Taking the 2gr-fse to new heights
#121
Driver School Candidate
Thread Starter
Sorry its been long but here's an update on the cammed is350 .
Now i have been in a race to get the car cammed between myself and a friend of mine , to which i lost and my friend won lol . I blew my original motor (without cams, motor went because the timing chains stretched and got caught with a guide and cracked the cylinder head) which caused me to used the spare motor so that i could have a running car. That was on top of having a 2nd kid, repairing the roof of my home and being in a car accident on top of that which caused this long delay. But I'm fine and now back to the great news! We finally have a cammed is350 and it sounds amazing, like a Chevy SS if I'm being honest. Now the car initially had a camshaft failure when the installed was first done. (A valve was bent after making contact with the piston . But the valve was replaced and the issue was corrected . (Not yet sure about what caused the issue but i will update you all when i am informed). Now this is what is done to the car for everyone that is interested and would like to do as well.
-Ported heads
-Ported manifold (upper and lower)
-Ported tundra TB (80mm)
-Ripp performance coilpacks-Nonstop tuning lightweight pulleys-MWR Stage 3 cams
- Titanium valves (MWR)
-Upgraded connected Rods (MWR)
-Stock pistons
Here are some pictures of the process and tomorrow i will upload a video soundclip of the car on my YouTube channel. But i hope you guys enjoy this.
Nonstop tuning lightweight pulley vs OEM
I hope you guys enjoy the update . I will post more on the car's first start up , idle and sounds tomorrow. The car idles very high since it's not tuned for the cams yet . But the great news is that the car is currently in the break in stage at the moment and may be getting tuned tomorrow .
-Ported heads
-Ported manifold (upper and lower)
-Ported tundra TB (80mm)
-Ripp performance coilpacks-Nonstop tuning lightweight pulleys-MWR Stage 3 cams
- Titanium valves (MWR)
-Upgraded connected Rods (MWR)
-Stock pistons
Here are some pictures of the process and tomorrow i will upload a video soundclip of the car on my YouTube channel. But i hope you guys enjoy this.
Nonstop tuning lightweight pulley vs OEM
I hope you guys enjoy the update . I will post more on the car's first start up , idle and sounds tomorrow. The car idles very high since it's not tuned for the cams yet . But the great news is that the car is currently in the break in stage at the moment and may be getting tuned tomorrow .
The following 5 users liked this post by Polo2is350:
2013FSport (02-27-22),
AMIRZA786 (02-25-22),
bob256k (02-24-22),
kenji211 (02-26-22),
redspencer (02-25-22)
#122
Lexus Champion
It sounds like you had a very interesting journey with some stumbles, but you made it! Congrats on all your hard work and patience
The following users liked this post:
Polo2is350 (02-24-22)
The following users liked this post:
Polo2is350 (02-25-22)
#124
Driver School Candidate
Thread Starter
We are estimating that the cams can allow the car to rev out to 8500rpms . But for reliability purposes, we are looking to push the limiter to 8000-8200rpms. I know with the stock cams , the 2grfse can rev out to 7600rpms and experience no valve float(it's been proven by a gentlemen in Puerto Rico who pushed his car everyday at that rev limit with no issues). The goal was to push the limiter to 8000rpms and we believe that we can absolutely achieve that !
The following users liked this post:
redspencer (02-25-22)
#125
Lexus Champion
iTrader: (1)
We are estimating that the cams can allow the car to rev out to 8500rpms . But for reliability purposes, we are looking to push the limiter to 8000-8200rpms. I know with the stock cams , the 2grfse can rev out to 7600rpms and experience no valve float(it's been proven by a gentlemen in Puerto Rico who pushed his car everyday at that rev limit with no issues). The goal was to push the limiter to 8000rpms and we believe that we can absolutely achieve that !
I see some nice big gains when Tuned in too. A few more q's please?
Did you use the same size Rods? Are they lighter? Did you consider doing longer Rods to Stroke to say a 3.7?
I spoke with a shop in Cali who has done Reground cams for the 2UZ. How did you come to you Cams specs? Or are those the Monkey Wrench cams? They have 3 Stages which one?
What Intake set up (Air Box) are you using?
What ECU Tune are you using to Tune with?
BTW: With all the life stuff you have going on, you did great with getting this done, and not being a "I'm going too do", who did nothing and did not show back up. Thanks for doing......and sharing!!
The following users liked this post:
Polo2is350 (02-25-22)
#126
Driver School Candidate
Thread Starter
I see some nice big gains when Tuned in too. A few more q's please?
Did you use the same size Rods? Are they lighter? Did you consider doing longer Rods to Stroke to say a 3.7?
I spoke with a shop in Cali who has done Reground cams for the 2UZ. How did you come to you Cams specs? Or are those the Monkey Wrench cams? They have 3 Stages which one?
What Intake set up (Air Box) are you using?
What ECU Tune are you using to Tune with?
BTW: With all the life stuff you have going on, you did great with getting this done, and not being a "I'm going too do", who did nothing and did not show back up. Thanks for doing......and sharing!!
Did you use the same size Rods? Are they lighter? Did you consider doing longer Rods to Stroke to say a 3.7?
I spoke with a shop in Cali who has done Reground cams for the 2UZ. How did you come to you Cams specs? Or are those the Monkey Wrench cams? They have 3 Stages which one?
What Intake set up (Air Box) are you using?
What ECU Tune are you using to Tune with?
BTW: With all the life stuff you have going on, you did great with getting this done, and not being a "I'm going too do", who did nothing and did not show back up. Thanks for doing......and sharing!!
#127
Lexus Champion
iTrader: (1)
The cams are Stage 3 from monkey wrench racing . The car will be remote tuned by RR racing, and the intake that's being used is the factory airbox (Fsport lower intake box) and the rods being used were from monkey wrench as well . Crower connecting rods which are lighter than OEM.
Did you consider a Custom like longer Rod? A Stoker Stroked IS370 of such. lol! Likely that would have cost to have done.
Most times a Bent valve is in assembly or the guide or something like that. I had that once on a Bike engine I built up. It’s sucks too. 1 valve wondering Why?
Last edited by jgscott; 02-25-22 at 01:36 PM.
#128
Driver School Candidate
Thread Starter
If you guys are interested on how a cammed is350 would sound. Here you go. The car is still in it's break in stage , but listen to that idle !
The following 5 users liked this post by Polo2is350:
2013FSport (02-27-22),
604GSE21 (02-26-22),
hfaltys (03-04-22),
redspencer (02-25-22),
the2ndr (01-10-23)
#129
Driver School Candidate
Thread Starter
Got it. Crower been around for a long time. Good Rods. Lighter is good for a faster throughout RPM. With that Pulley and Rods that thing should rip through the spinning fast. Nice. Thanks. I’m impressed.
Did you consider a Custom like longer Rod? A Stoker Stroked IS370 of such. lol! Likely that would have cost to have done.
Most times a Bent valve is in assembly or the guide or something like that. I had that once on a Bike engine I built up. It’s sucks too. 1 valve wondering Why?
Did you consider a Custom like longer Rod? A Stoker Stroked IS370 of such. lol! Likely that would have cost to have done.
Most times a Bent valve is in assembly or the guide or something like that. I had that once on a Bike engine I built up. It’s sucks too. 1 valve wondering Why?
#130
Lexus Champion
iTrader: (1)
If you guys are interested on how a cammed is350 would sound. Here you go. The car is still in it's break in stage , but listen to that idle !
https://youtu.be/VpnL0Ouokqc
https://youtu.be/VpnL0Ouokqc
You did some good research and put it together. That 2GR is something! Sounds real Nasty, On Rev's, with the quicker spinning rev happy motor with the Porting and enlargements and that can breath too @8000rpm. Hang on!!! I love it! lol!
The following users liked this post:
Polo2is350 (02-25-22)
#131
Lexus Champion
If you guys are interested on how a cammed is350 would sound. Here you go. The car is still in it's break in stage , but listen to that idle !
https://youtu.be/VpnL0Ouokqc
https://youtu.be/VpnL0Ouokqc
Last edited by AMIRZA786; 02-25-22 at 04:05 PM.
The following users liked this post:
Polo2is350 (02-25-22)
#132
Instructor
BRUH.
I thought you meant STOCK CHEVY SS.
That sounds EVIL. I dont even care if the car isn't a V8 that sounds NASTY.
BRB bought to mod my GS350 🤣🤣🤣
I thought you meant STOCK CHEVY SS.
That sounds EVIL. I dont even care if the car isn't a V8 that sounds NASTY.
BRB bought to mod my GS350 🤣🤣🤣
The following users liked this post:
Polo2is350 (02-26-22)
#133
If you guys are interested on how a cammed is350 would sound. Here you go. The car is still in it's break in stage , but listen to that idle !
https://youtu.be/VpnL0Ouokqc
https://youtu.be/VpnL0Ouokqc
The following 2 users liked this post by redspencer:
jgscott (02-25-22),
Polo2is350 (02-26-22)
#134
Lexus Test Driver
iTrader: (2)
Polo, hats off to your build here! Looking forward to your grin and some dyno pulls!
Titanium rods, valves, and retainers should promote some great throttle response!
You do anything to the transmission? This might be a good case for shift kit and main pressure increase. That said, they seem to hold up with boost, so you should be okay...
Like everyone else, looking forward to the ride along and drive by!
GL!
Titanium rods, valves, and retainers should promote some great throttle response!
You do anything to the transmission? This might be a good case for shift kit and main pressure increase. That said, they seem to hold up with boost, so you should be okay...
Like everyone else, looking forward to the ride along and drive by!
GL!
#135
Driver School Candidate
Thread Starter
Polo, hats off to your build here! Looking forward to your grin and some dyno pulls!
Titanium rods, valves, and retainers should promote some great throttle response!
You do anything to the transmission? This might be a good case for shift kit and main pressure increase. That said, they seem to hold up with boost, so you should be okay...
Like everyone else, looking forward to the ride along and drive by!
GL!
Titanium rods, valves, and retainers should promote some great throttle response!
You do anything to the transmission? This might be a good case for shift kit and main pressure increase. That said, they seem to hold up with boost, so you should be okay...
Like everyone else, looking forward to the ride along and drive by!
GL!
Last edited by Polo2is350; 02-27-22 at 06:07 PM.