The last exhaust modification in Mexico (and it was a good one)
04-06-08, 03:37 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
Now, you will notice at the top of the picture much better spacing between propeller shaft brace and the cat.
Attached Thumbnails
04-06-08, 03:39 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
Now, we needed to make some more space for the muffler on the rear end (we knew this from previous measurements), so we had to cut these short extension pieces.
Attached Thumbnails
04-06-08, 03:40 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
Another shot
Attached Thumbnails
04-06-08, 03:41 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
And the piece coming off.
Attached Thumbnails
04-06-08, 03:43 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
And then working on the other side.
Attached Thumbnails
04-06-08, 03:44 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
And the result.
Attached Thumbnails
04-06-08, 03:48 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
Here we angle the pieces inward.
Attached Thumbnails
04-06-08, 03:49 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
Now, before we take a look at the muffler, I want to show the shop. Here we see some of the prepackaged mufflers ready for shipment along with some glasspacks.
Attached Thumbnails
04-06-08, 03:51 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
These machines help put small holes into the interior tubes of the mufflers (that reach the fiberglass that is stuck inside the mufflers).
Attached Thumbnails
04-06-08, 03:53 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
Some more stamping equipment
Attached Thumbnails
04-06-08, 03:54 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
Some of the oval muffler bodies and the bigger presses.
Attached Thumbnails
04-06-08, 03:55 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
We will see this machine later, it has an interesting purpose.
Attached Thumbnails
04-06-08, 03:56 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
Some more glasspacks.
Attached Thumbnails
04-06-08, 03:58 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
A muffler and some of the interior piping. If you remember the earlier machine that punches the holes into these pipes, well this is the result.
Attached Thumbnails
04-06-08, 03:59 PM
Super Moderator
Thread Starter
Join Date: Apr 2004
Location: Miami, Florida
Posts: 17,246
One of their round mufflers.
Attached Thumbnails