Headlights
03-12-09, 05:27 PM
#31
Driver School Candidate
Join Date: Apr 2008
Location: pa
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
uhmmm, those leveling screws.... %$#%%&% do ya think they could put them anywhere more unaccessable? cripes you need tiny little kid hands to access the one furthest on the passenger side... and they put phillips head screw head on them.. oh yea riiiight.. no screwdriver i know would ever fit in there.. 
03-12-09, 09:50 PM
#32
Pole Position
Join Date: Sep 2008
Location: Rhode Island
Posts: 363
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, they're pretty hard to get at lol.
I just used a small ratchet with whatever size it is. Turn the counter clockwise to raise, clockwise to lower.
There are a total of 3 screws. One under the high beam, one next to the low beam, and one next to the fog bulb that you shouldn't touch.
Turn the one below the high beam and one next to the low beam equally.
That will work perfectly
I just used a small ratchet with whatever size it is. Turn the counter clockwise to raise, clockwise to lower.
There are a total of 3 screws. One under the high beam, one next to the low beam, and one next to the fog bulb that you shouldn't touch.
Turn the one below the high beam and one next to the low beam equally.
That will work perfectly
Last edited by cduluk; 03-12-09 at 09:56 PM.
03-13-09, 06:22 AM
#33
Lexus Champion
i would take a photo, but my sensor isnt installed there anymore now that ive wired it into the cabin for manual control. If you look under your right rear tire you'll see sort of like two little arms between the control arm and the underbelly. Just take a look and you'll find it...
03-13-09, 12:47 PM
#36
Driver School Candidate
Join Date: Apr 2008
Location: pa
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
isnt it the truth lexus114? here i am struggling to turn a few lousy screws and this genius is pulling off amazing stunts.... oh to be young again. well, and have an eye for aesthetic fun stuff and some talent too...
then there is lexmex, the genius mechanic.
i sort of feel dumb, lol
then there is lexmex, the genius mechanic.
i sort of feel dumb, lol
03-14-09, 03:57 PM
#40
Driver School Candidate
Join Date: Apr 2008
Location: pa
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
well....
to be truthful, im on my second 8mm ratchet head wrench... &$#%^& , the furthest screw on the passenger side is pi$$ing me off royally. the first ratchet had too much play, no room in the compartment could not manage one lousy turn
, this new wrench i have not even tried yet.. i'm procrastinating: 
you want i buy you a plane ticket to my area? you fix up my ride, i then send you back home... all while i set in my recliner sipping gray goose and cranberry
to be truthful, im on my second 8mm ratchet head wrench... &$#%^& , the furthest screw on the passenger side is pi$$ing me off royally. the first ratchet had too much play, no room in the compartment could not manage one lousy turn
, this new wrench i have not even tried yet.. i'm procrastinating: you want i buy you a plane ticket to my area? you fix up my ride, i then send you back home...
all while i set in my recliner sipping gray goose and cranberry
03-14-09, 04:00 PM
#41
Pole Position
Join Date: Sep 2008
Location: Rhode Island
Posts: 363
Likes: 0
Received 0 Likes
on
0 Posts
haha... if you lived in Florida or somewhere warm i might take you up on that :P
I just used a tiny socket and wrench, after the first few turns i just turned the socket with my hands.
I just used a tiny socket and wrench, after the first few turns i just turned the socket with my hands.
03-16-09, 06:30 AM
#45
Lexus Champion
hey "c",i cleaned my leveling sensor yesterday.it was nice and clean inside,but the outside was pretty dirty.praxis,your rubber o ring must have not sealed properly for it to get that dirty inside.now,qoustion for you c,is their a way to lube the little motors that move the headlights up/down?? or is it too involved?
Last edited by lexus114; 03-16-09 at 06:59 AM.
Thread
Thread Starter
Forum
Replies
Last Post
Lovecorond
RX - 1st Gen (1999-2003)
1
01-31-18 04:15 PM
