Enable the Seat Belt chime?
#1
Driver School Candidate
Thread Starter
Join Date: Dec 2009
Location: WI
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Enable the Seat Belt chime?
I have tried the following steps already on a 2004--RX330, but no luck..any other suggestions?
Here is the instruction for reseting seat belt buzzers;
1. Turn the ignition switch to ON position
2. Press the ODO/Trip switch until the odometer display "ODO"
3. Turn the ignition switch off.
4. Turn the ignition switch to the ON position.
5. Press the ODO/Trip switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6. Continue holding down the ODO/trip switch and fasten the driver side seat belt.
7. Check that the odometer display either "b-on" or "b-off".
8. Press the ODO/Trip switch to change the display to "b-off".
9. Turn ignition switch off.
10. You are done.
Here is the instruction for reseting seat belt buzzers;
1. Turn the ignition switch to ON position
2. Press the ODO/Trip switch until the odometer display "ODO"
3. Turn the ignition switch off.
4. Turn the ignition switch to the ON position.
5. Press the ODO/Trip switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6. Continue holding down the ODO/trip switch and fasten the driver side seat belt.
7. Check that the odometer display either "b-on" or "b-off".
8. Press the ODO/Trip switch to change the display to "b-off".
9. Turn ignition switch off.
10. You are done.
#3
Driver School Candidate
Thread Starter
Join Date: Dec 2009
Location: WI
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
#4
You, of course, do the same procedure above, but at the end you want to leave it in the "b-on" state.
"b-on" means seat belt chime is on
"b-off" means seat belt chime is disabled.
"b-on" means seat belt chime is on
"b-off" means seat belt chime is disabled.
#6
Driver School Candidate
Join Date: Sep 2020
Location: FCT
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
I have tried the following steps already on a 2004--RX330, but no luck..any other suggestions?
Here is the instruction for reseting seat belt buzzers;
1. Turn the ignition switch to ON position
2. Press the ODO/Trip switch until the odometer display "ODO"
3. Turn the ignition switch off.
4. Turn the ignition switch to the ON position.
5. Press the ODO/Trip switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6. Continue holding down the ODO/trip switch and fasten the driver side seat belt.
7. Check that the odometer display either "b-on" or "b-off".
8. Press the ODO/Trip switch to change the display to "b-off".
9. Turn ignition switch off.
10. You are done.
Here is the instruction for reseting seat belt buzzers;
1. Turn the ignition switch to ON position
2. Press the ODO/Trip switch until the odometer display "ODO"
3. Turn the ignition switch off.
4. Turn the ignition switch to the ON position.
5. Press the ODO/Trip switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6. Continue holding down the ODO/trip switch and fasten the driver side seat belt.
7. Check that the odometer display either "b-on" or "b-off".
8. Press the ODO/Trip switch to change the display to "b-off".
9. Turn ignition switch off.
10. You are done.
#7
Driver School Candidate
Join Date: Sep 2020
Location: FCT
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
I have tried the following steps already on a 2004--RX330, but no luck..any other suggestions?
Here is the instruction for reseting seat belt buzzers;
1. Turn the ignition switch to ON position
2. Press the ODO/Trip switch until the odometer display "ODO"
3. Turn the ignition switch off.
4. Turn the ignition switch to the ON position.
5. Press the ODO/Trip switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6. Continue holding down the ODO/trip switch and fasten the driver side seat belt.
7. Check that the odometer display either "b-on" or "b-off".
8. Press the ODO/Trip switch to change the display to "b-off".
9. Turn ignition switch off.
10. You are done.
Here is the instruction for reseting seat belt buzzers;
1. Turn the ignition switch to ON position
2. Press the ODO/Trip switch until the odometer display "ODO"
3. Turn the ignition switch off.
4. Turn the ignition switch to the ON position.
5. Press the ODO/Trip switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6. Continue holding down the ODO/trip switch and fasten the driver side seat belt.
7. Check that the odometer display either "b-on" or "b-off".
8. Press the ODO/Trip switch to change the display to "b-off".
9. Turn ignition switch off.
10. You are done.
Thread
Thread Starter
Forum
Replies
Last Post
kbbean08
IS - 3rd Gen (2014-present)
39
03-16-19 01:10 PM