Lowered and TSX Retrofitted. Pictures!
03-26-08, 06:39 PM
#31
Pole Position
Thread Starter
Join Date: Apr 2007
Location: Alberta
Posts: 353
Likes: 0
Received 0 Likes
on
0 Posts
Yeop got the whole TSX headlight assembly from a seller so I was sure there were no scratches on the lenses. hey your the one with the upgraded clear lense fogs right? Im thinking of replacing my lenses cause i forgot to ground one of them when i installed the bulb and it exploded and melted one of the insides. where did you pick yours up?
Last edited by SC30096; 03-26-08 at 06:48 PM.
03-26-08, 07:05 PM
#32
Pole Position
iTrader: (6)
Join Date: Feb 2008
Location: Texas
Posts: 346
Likes: 0
Received 0 Likes
on
0 Posts
Here are some pics mine have slight bit more glare but not much its mostly the old crappy camera. In person theres no where near as much glare. I still need to do some adjusting to.
Last edited by tcrow31; 03-26-08 at 07:10 PM.
03-26-08, 07:42 PM
#35
Pole Position
Thread Starter
Join Date: Apr 2007
Location: Alberta
Posts: 353
Likes: 0
Received 0 Likes
on
0 Posts
well I do agree that your stock cut off is more sharper then mine which is probably from the delining but I wouldnt know cause I didnt deline before I retrofitted. but from the picture there is substaintial amount of glare. and for oncoming traffic at greater distances i used to get flashed. One other thing is that the light distrubition is still no where near the same as the TSX, the old projectors will always have the hot spots. PNP still kicks halgeons to the curb 3 fold but retrofit also does the same to PNP
Last edited by SC30096; 03-26-08 at 08:15 PM.
03-26-08, 08:17 PM
#39
Pole Position
iTrader: (6)
Join Date: Feb 2008
Location: Texas
Posts: 346
Likes: 0
Received 0 Likes
on
0 Posts
well I do agree that your cut off is more sharper then mine which is probably from the delining but I wouldnt know cause I didnt deline before I retrofitted. but from the picture there is substaintial amount of glare. and for oncoming traffic at greater distances i used to get flashed. One other thing is that the light distrubition is still no where near the same as the TSX, the old projectors will always have the hot spots. PNP still kicks halgons to the curb 3 fold but retrofit also does the same to PNP
03-27-08, 12:29 PM
#45
Pole Position
Thread Starter
Join Date: Apr 2007
Location: Alberta
Posts: 353
Likes: 0
Received 0 Likes
on
0 Posts
Thanks!
Im not trying to put you down or anything like i mean your cutoff is probably the sharpest that i've seen in pictures as far as the old projectors go but yeah retrofit is just another level.
get those pictures up when your finished.
with the basic tools and a little patience this job isnt that hard to do.
haha well if your really serious about it I would suggest maybe you start finding the parts needed for the job.
was this just for the parts?or labor costs as well?
Yea the pictures show more glare than there really is though. In person it doesn't look like that. Dunno if its the crappy camera or what but in person you can see the two rise in the cut off lines clear as day, but defiantly the retrofit gives a better light distribution and no hot spots like mine.
get those pictures up when your finished.
with the basic tools and a little patience this job isnt that hard to do.
was this just for the parts?or labor costs as well?