What did you do to your SC today?
The following users liked this post:
joe diego (05-30-19)
#7608
^^ Bravo!!
Replaced a broken caliper and bled brakes. I can stop again!
Also got *most of the condensation out of this headlight. Probably polish them tomorrow
before
After
Oh, and Installed a new parking light bulb also on this side (as seen above) Had to use the pliers I won’t lie lol
Replaced a broken caliper and bled brakes. I can stop again!
Also got *most of the condensation out of this headlight. Probably polish them tomorrow
before
After
Oh, and Installed a new parking light bulb also on this side (as seen above) Had to use the pliers I won’t lie lol
#7609
Pliers? I was ready to take a torch to mine.
The following users liked this post:
Dokuji (06-01-19)
The following users liked this post:
LEXXIUM (06-04-19)
#7611
^^^ dang, he put the towel down and everything. got lucky i didnt have to do that. at the most had one car seat back there with a booster seat. then, my oldest got big enough to sit shotgun
The following users liked this post:
Dokuji (06-03-19)
#7612
hahah! tried it out today, wan't bad getting them in and out at all! theyre both pretty little still. I bought these seats specifically for their size. they dont stick out any further than the seats do, or any higher, as you can see. so it's no harder than letting the auto seats do their job and crawling back there a bit to get them snugged.
They liked the ride! I was worried the 1uz might be a bit too loud for them but they were digging the vroom vroom
also, that ain't no towel its a full size microfiber bedspread man. only the best for the SC. LOL!!! too bad there are already tears in the seat backs, or i might have bothered to cover those up too XD
They liked the ride! I was worried the 1uz might be a bit too loud for them but they were digging the vroom vroom
also, that ain't no towel its a full size microfiber bedspread man. only the best for the SC. LOL!!! too bad there are already tears in the seat backs, or i might have bothered to cover those up too XD
The following users liked this post:
SCJim (06-03-19)
#7614
Last night installed new tires and spacers. Today have dialed in suspension to this for now. I think I can safely go mayyyybe 1/4” more in the fronts. But I’m going to drive like this for a bit and see how many incidents I have. O.O
Trust me, I closed the gap in the fronts and couldn’t even get out of the garage 1/4 more mayyybe
all part of my silly quest to make 17s look good. I’m getting close!
worst case, I'll raise the rears 3/8" to level it a bit and call it good (pussing out)
Trust me, I closed the gap in the fronts and couldn’t even get out of the garage 1/4 more mayyybe
all part of my silly quest to make 17s look good. I’m getting close!
worst case, I'll raise the rears 3/8" to level it a bit and call it good (pussing out)
Last edited by Dokuji; 06-04-19 at 10:33 AM.
The following users liked this post:
SCJim (06-04-19)
#7615
I think that your 17s look nice - definitely much better than mine ever did. For me 18s are perfect but I have seen SCs with 19s that looked really nice too. But we all have to look out for our bang for the buck and you are rocking those 17s.
I would think that leaving the front where it is and raising the rear to get back that nice stance the SC has from the factory would look very nice. That is pretty close to what I want to hit with my new 18s once I get around to coilovers.
Looking Good and looking forward to seeing where it ends up.
I would think that leaving the front where it is and raising the rear to get back that nice stance the SC has from the factory would look very nice. That is pretty close to what I want to hit with my new 18s once I get around to coilovers.
Looking Good and looking forward to seeing where it ends up.
The following users liked this post:
Dokuji (06-04-19)
#7616
Thanks man! I'm trying lol! The idea i had in my head was correct aesthetically, but i underestimated how low the subframe is hanging down there. So ill have to keep adjusting it til I find the perfect balance. It's close though.
yeah I am thinking to raise the rears a half inch. I like where theyre at but since i can't go much lower in the front it'll help even things out.
I appreciate the support!
yeah I am thinking to raise the rears a half inch. I like where theyre at but since i can't go much lower in the front it'll help even things out.
I appreciate the support!
The following users liked this post:
SCJim (06-05-19)
#7618
got the CD009 in, gonna weld a swan neck shifter to it because currently the back of my arm hits the seat in 2nd, 4th, and 6th gears. should have just gotten the shifter relocation kit lol but whatever i guess.
#7620