Tinting isn't supposed to be this hard....
#1
Tinting isn't supposed to be this hard....
A couple months ago I got some 20% Tint for the passengers side window from Wally World. The Drivers side had 50% tint I think. This is a 1992 SC400 as you all probably know, But anyway, The first time I tried tinting the window, it creased and wasn't sliding around, (btw, I used boatloads of soapy water to apply), and it was windy anyway so I wasted that tinting. I threw it away. Later, when I finally got it into the garage, (no wind and such), we got to applying the tint, again. Like usual, used lots of soapy water cuts were really good, but than near the end there the tint creased. Look's like crap up close but the tint is still blocking the sun from the interior. (back windows aren't done either). My Question: Is tinting supposed to be this hard? My Dad said he tinted his Isuzu Trooper when he got it new in the early 90s, and that is was like breathing. As for the SC400, the window goes all 4 ways. The molding of the window is up, down, left, right, everywhere. Has anyone else DIY the tinting on their SC? And if so, how hard was it? It is just really hard for me to tint these windows. My Dad was helping too and he was surprised that it was so difficult, or is it meant out to be a Tint shop thing? That will cost me money I don't have on something that isn't that hard. Thoughts?
#2
Lexus Champion
iTrader: (10)
Did you heat shrink it? The windows of our SC's are curved unlike other cars. Heat shrinking the tint is really necessary. Plus, if the window weather gaskets are dry and the furry finish is gone, then the tint wouldn't slide in like its supposed too even with lotsa soapy water.
#4
Did you heat shrink it? The windows of our SC's are curved unlike other cars. Heat shrinking the tint is really necessary. Plus, if the window weather gaskets are dry and the furry finish is gone, then the tint wouldn't slide in like its supposed too even with lotsa soapy water.
#6
Lexus Champion
iTrader: (10)
I have never heard of heat shrinking it...that sounds like it would work...so would it melt the creases to were you don't notice them or do you have to start out without creases completely. My window gaskets are really good condition but I don't know what you mean by furry finish...Nice to see you by the way Kingphilip, you haven't posted lately that I've noticed..thanks so much for the pro tip! I will end up re doing the tint if the car doesn't sell...
#7
You're getting the idea. You can watch some DIY vids on YouTube on how to do it. It takes a few couple tries to get it right. Also, the sticky part of the tint is really really sensitive, so wind blows dust'll get to it that quick and the tint is trash, if it comes in contact with anything, dust gets to it and again it's trash. So you really need to do it indoors and be really really careful. Check the side of the window gasket that's in contact with the glass window, it should look like furry, like felt paper. If the furr is gone, then the rubber is the one in contact to the glass, and that'll push the tint enough to make it stick to glass as you try to slide it downwards. I do tinting occasionally. And took me a few couple tries my first time doing it. I've always been here on CL, just moving slow, 'cause September was a bday month for my family, and now Xmas is coming... Lol Ballin' on a budget 'til after the holidays...
Trending Topics
#10
Lexus Champion
iTrader: (10)
OOOOH, okay...that furry felt fuzz between the window and the rubber trim! I know what your talking about now. Yes, it is all still there. They should have a name for that fuzz...any pointers on tinting the curved windows? (tricks and such) Thanks for the tips and help! I stink at tinting so this is really helpful.
#11
You're gonna need a heat gun to heat shrink the tint. Only advice I can give you is when you're heating it, use gloves or a damp cloth to wipe the 'fingers' (bubbles) out while heating it. And try to heat as much area as you can, don't focus on just one area in particular, 'cause after heating it a few times it'll melt the tint, which is obviously bad. It takes a lot of practice before you can get a hang of it, by the time you're good at it, it's like paying a shop to do it for you already, lol.