sc300 TH400 Kit/TEC 3
08-31-07, 09:22 PM
#1
Lead Lap
Thread Starter
iTrader: (2)
Join Date: Dec 2006
Location: nv
Posts: 543
Likes: 0
Received 0 Likes
on
0 Posts
sc300 TH400 Kit/TEC 3
i have a full TH400 kit for the sc300 for sale
it came off of Hal's 98 sc300 that runs low 9's @ 150 +
i was told that since it came off his car it has been refreshed and ready to go.
it comes with
TH400 tranny with toyota bellhousing (direct bolt on)
(reverse shift pattern and manual drive body)
bradco torque converter- 3500 RPM stall
cutsom one piece driveshaft 4" (?) from tranny to differential
two tranny coolers with lines and fittings
Quiksilver shifter
4.27 rear diff (welded- acts like an LSD)
pretty much your entire drive train system ready to bolt up to a GE or GTE motor and go!
it's been sitting in my garage ever since i bought it and was thinking about putting it on a sc300. but my project seem to be on hold for now so i won't need this (indefinitely).
$3200 shipped!!!
it retails for $5000+ !
Electromotive TEC3
also this is from Hal's SC300
if you guys aren't familiar with it, it's very clean, fast and proven.
i don't know much about this unit but it pretty much includes EVERYTHING needed to strap on and go.
it is a standalone ECU including wiring harness, direct ignition coils, crank trigger wheel, etc.
$1300 SOLD!!!
it came off of Hal's 98 sc300 that runs low 9's @ 150 +
i was told that since it came off his car it has been refreshed and ready to go.
it comes with
TH400 tranny with toyota bellhousing (direct bolt on)
(reverse shift pattern and manual drive body)
bradco torque converter- 3500 RPM stall
cutsom one piece driveshaft 4" (?) from tranny to differential
two tranny coolers with lines and fittings
Quiksilver shifter
4.27 rear diff (welded- acts like an LSD)
pretty much your entire drive train system ready to bolt up to a GE or GTE motor and go!
it's been sitting in my garage ever since i bought it and was thinking about putting it on a sc300. but my project seem to be on hold for now so i won't need this (indefinitely).
$3200 shipped!!!
it retails for $5000+ !
Electromotive TEC3
also this is from Hal's SC300
if you guys aren't familiar with it, it's very clean, fast and proven. i don't know much about this unit but it pretty much includes EVERYTHING needed to strap on and go.
it is a standalone ECU including wiring harness, direct ignition coils, crank trigger wheel, etc.
$1300 SOLD!!!
Last edited by tuninghaus; 10-17-07 at 01:16 PM.
10-01-07, 07:06 PM
#4
Driver
Join Date: Dec 2005
Location: FL
Posts: 143
Likes: 0
Received 0 Likes
on
0 Posts
i have a full TH400 kit for the sc300 for sale
it came off of Hal's 98 sc300 that runs low 9's @ 150 +
i was told that since it came off his car it has been refreshed and ready to go.
it comes with
TH400 tranny with toyota bellhousing (direct bolt on)
(reverse shift pattern and manual drive body)
bradco torque converter- 3500 RPM stall
cutsom one piece driveshaft 4" (?) from tranny to differential
two tranny coolers with lines and fittings
Quiksilver shifter
4.27 rear diff (welded- acts like an LSD)
pretty much your entire drive train system ready to bolt up to a GE or GTE motor and go!
it's been sitting in my garage ever since i bought it and was thinking about putting it on a sc300. but my project seem to be on hold for now so i won't need this (indefinitely).
$3800!!
Electromotive TEC3
also this is from Hal's SC300 if you guys aren't familiar with it, it's very clean, fast and proven.
i don't know much about this unit but it pretty much includes EVERYTHING needed to strap on and go.
it is a standalone ECU including wiring harness, direct ignition coils, crank trigger wheel, etc.
$1300 SOLD!!!
it came off of Hal's 98 sc300 that runs low 9's @ 150 +
i was told that since it came off his car it has been refreshed and ready to go.
it comes with
TH400 tranny with toyota bellhousing (direct bolt on)
(reverse shift pattern and manual drive body)
bradco torque converter- 3500 RPM stall
cutsom one piece driveshaft 4" (?) from tranny to differential
two tranny coolers with lines and fittings
Quiksilver shifter
4.27 rear diff (welded- acts like an LSD)
pretty much your entire drive train system ready to bolt up to a GE or GTE motor and go!
it's been sitting in my garage ever since i bought it and was thinking about putting it on a sc300. but my project seem to be on hold for now so i won't need this (indefinitely).
$3800!!
Electromotive TEC3
also this is from Hal's SC300
if you guys aren't familiar with it, it's very clean, fast and proven. i don't know much about this unit but it pretty much includes EVERYTHING needed to strap on and go.
it is a standalone ECU including wiring harness, direct ignition coils, crank trigger wheel, etc.
$1300 SOLD!!!
Thread
Thread Starter
Forum
Replies
Last Post
