CA FS: full header back exhaust system, APEXI tip + APEXI ECV
#1
Lexus Champion
Thread Starter
iTrader: (53)
Join Date: Apr 2008
Location: CA
Posts: 3,240
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://www.clublexus.com/forums/images/icons/icon1.gif)
bolt on application: 92-97 sc300's
![](http://i304.photobucket.com/albums/nn197/anteatsrice/apexi.jpg)
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6417.jpg)
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6424.jpg)
2"
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6425.jpg)
2.5"
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6427.jpg)
3"
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6430.jpg)
4.5" tip
*units shown in the picture are in mm*
there is also a flange at where the 76mm piping begins. also the flange on the rear section may need to clocked a few degrees so you can get the proper pipe bends into location of the undercarriage. about a 20-50 bucks job at an exhuast shop.
this setup was formally bigwavesc's setup, and he claimed it was a drastic improvement for the N/A application. up to 40hp gains he said! [drifting use, mainly WOT]
asking 200 picked up.
APEXI exhaust control valve
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6435.jpg)
opened but never used. works great.
asking 150 picked up, or 180 shipped
or you can buy both for 325
parts are located in 92126
but pming is just as fine
thanks for looking!
![](http://i304.photobucket.com/albums/nn197/anteatsrice/apexi.jpg)
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6417.jpg)
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6424.jpg)
2"
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6425.jpg)
2.5"
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6427.jpg)
3"
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6430.jpg)
4.5" tip
*units shown in the picture are in mm*
there is also a flange at where the 76mm piping begins. also the flange on the rear section may need to clocked a few degrees so you can get the proper pipe bends into location of the undercarriage. about a 20-50 bucks job at an exhuast shop.
this setup was formally bigwavesc's setup, and he claimed it was a drastic improvement for the N/A application. up to 40hp gains he said! [drifting use, mainly WOT]
asking 200 picked up.
APEXI exhaust control valve
![](https://i304.photobucket.com/albums/nn197/anteatsrice/IMG_6435.jpg)
opened but never used. works great.
asking 150 picked up, or 180 shipped
or you can buy both for 325
parts are located in 92126
but pming is just as fine
thanks for looking!
Last edited by rwdanthony; 01-23-10 at 10:55 AM.