GA SC300 aluminum flywheel + turbo, highflow cat, ic piping, oem 18" wheel
10-25-10, 07:15 PM
#1
SC300 aluminum flywheel + turbo, highflow cat, ic piping, oem 18" wheel
Im trying to clean out my closet in the office. so heres what I got.
Flywheel:
-Clutchmasters Lightweight Aluminum Flywheel
-Fits SC300 or 1jzgte with W58 trans
-Will need a new insert which can be purchased from clutchmasters for roughly 80 dollars
price: SOLD!
pic
Wheel:
-18" OEM Lexus upgrade. has some scratches on it, seen in photo. I was going to make a complete set but ended up just buying aftermarket.
18x8 +45 offset
price: $25 + shipping
pic
Turbo:
AiResearch T04 turbo
0.60 A/R Compressor housing
0.68 A/R Exhaust Housing
T4 Flange
3" inlet
2" intake outlet
3" V-Band Exhaust outlet
comes with new turbo feed line pre heat wrapped with DEI insulation
About: It was on my 1jz car when I got it. It worked great when it was on it. spooled lightning fast too but I needed something bigger to get the hp numbers I was looking for.
price: SOLD!
pic
High Flow Cat:
3" inlet, 3" outlet highflow cat. sized for a standard v8 motor.
Used for literally one day.
price: $75 + shipping
Pic
Intercooler Piping:
Just some spare pipe I had laying around. 2.5" aluminum. mandrel bent. comes with a 4" intake filter
Price: $30 + Shipping
pic
Flywheel:
-Clutchmasters Lightweight Aluminum Flywheel
-Fits SC300 or 1jzgte with W58 trans
-Will need a new insert which can be purchased from clutchmasters for roughly 80 dollars
price: SOLD!
pic
Wheel:
-18" OEM Lexus upgrade. has some scratches on it, seen in photo. I was going to make a complete set but ended up just buying aftermarket.
18x8 +45 offset
price: $25 + shipping
pic
Turbo:
AiResearch T04 turbo
0.60 A/R Compressor housing
0.68 A/R Exhaust Housing
T4 Flange
3" inlet
2" intake outlet
3" V-Band Exhaust outlet
comes with new turbo feed line pre heat wrapped with DEI insulation
About: It was on my 1jz car when I got it. It worked great when it was on it. spooled lightning fast too but I needed something bigger to get the hp numbers I was looking for.
price: SOLD!
pic
High Flow Cat:
3" inlet, 3" outlet highflow cat. sized for a standard v8 motor.
Used for literally one day.
price: $75 + shipping
Pic
Intercooler Piping:
Just some spare pipe I had laying around. 2.5" aluminum. mandrel bent. comes with a 4" intake filter
Price: $30 + Shipping
pic
Last edited by fleishelja; 11-05-10 at 07:34 AM.
10-26-10, 01:58 PM
#7
-Im not sure of the exact weight difference. the aluminum one is pretty light though. I'll post the part number tonight.
-I'm in roswell
-I believe the difference is that the stock 1jz uses an r154 transmission. therefore the flywheel is different.
-there is no shaft play in the turbo and it didnt smoke at all when it was removed.
-I'm in roswell
-I believe the difference is that the stock 1jz uses an r154 transmission. therefore the flywheel is different.
-there is no shaft play in the turbo and it didnt smoke at all when it was removed.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
vindedreal
General Classifieds
1
04-18-10 11:38 AM
