AL WTB: 1JZGTE parts
#1
1JZ Single SC400
Thread Starter
iTrader: (59)
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Received 15 Likes
on
12 Posts
WTB: 1JZGTE parts
I am needing a few parts to start my swap next month. If you have any of these in really good shape, post or pm me. Must post pictures or email me with them to marklinley36@gmail.com. If you have something that you might think I need then let me know. These are just to get me started.
SC300 radiator fan shroud
SC300 AC lines from fire wall to compressor
TT fuel pump or walbro 255
boost controller
BOV 40 or more
Turbo,let me what you have. Maybe 60-67 with .70 AR
Manifold with extra strength welds
Engine gasket and seal set
SC300 upper and lower radiator hoses, new or barely used with clamps
FMIC, let me know what you have and size inlets and outlets with dimensions
TT fan
R154 clutch with pressure plate, must be at least stage 3 and minimum wear.
Thanks guys!
SC300 radiator fan shroud
SC300 AC lines from fire wall to compressor
TT fuel pump or walbro 255
boost controller
BOV 40 or more
Turbo,let me what you have. Maybe 60-67 with .70 AR
Manifold with extra strength welds
Engine gasket and seal set
SC300 upper and lower radiator hoses, new or barely used with clamps
FMIC, let me know what you have and size inlets and outlets with dimensions
TT fan
R154 clutch with pressure plate, must be at least stage 3 and minimum wear.
Thanks guys!
#3
Lead Lap
iTrader: (3)
Join Date: Sep 2010
Location: LA
Posts: 456
Likes: 0
Received 0 Likes
on
0 Posts
I have the fan shroud and ac lines, possibly the upper and lower radiator hoses. For fastest results, email me at sales@redzonline.com and be sure to put SC300 in the subject and include your postal code for shipping quotes.
#6
Lead Lap
iTrader: (3)
I have a twin plate spec clutch with about 2000mi it has almost no wear on clutches and pressure plates it comes with lines, flywheel etc. the hydraulic throwout bearing failed and it needs a new one for about $125 I believe.
$900obo if you are seriously interested I will send you pictures.
$900obo if you are seriously interested I will send you pictures.
#7
1JZ Single SC400
Thread Starter
iTrader: (59)
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Received 15 Likes
on
12 Posts
Was looking for a single but i am always interesed. Why are you selling it? For a r154?
Also looking for the clutch cylinder and the five speed pedals with ALL hardware. A five speed cover with the heated seats options as well in very good shape.
Also looking for the clutch cylinder and the five speed pedals with ALL hardware. A five speed cover with the heated seats options as well in very good shape.
Trending Topics
#9
Lead Lap
iTrader: (3)
Im selling it because it was a pain in the *** to install. if you do it with the engine in the car you have to lower about 10 bolts that hold your sub frame to the car and your strut bolts so that you have enough room to stab the transmission because its a lot thicker setup than stock and its not a pull type clutch hints the hyd throwout. The clutch was very strong and extremely hard pedal feel it was just overkill for me. Its made to hold about 900ft lbs of torque. I still haven't even gotten a fuel system to push me past the 500whp mark when the hyd throwout failed I just decided to go with something easier to install/remove and softer pedal feel. I dont have any other parts except maybe a slave cylinder.
#10
Lead Lap
iTrader: (3)
I also have a single disk ogura racing clutch setup with flywheel, pull to push conversion parts. The flywheel and 2 piece pressure plate are good but it needs a new disk for around $175. I'll sale this for $250. I believe its the 409 model.
I also have a stage 3 action pressure plate by it self with about 10,000 daily driving use and normal wear and tear. $100.
pm me for a fast response
I also have a stage 3 action pressure plate by it self with about 10,000 daily driving use and normal wear and tear. $100.
pm me for a fast response
#14
1JZ Single SC400
Thread Starter
iTrader: (59)
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Received 15 Likes
on
12 Posts
Found fan, fan shroud, radiator with mounts, tt fuel pump, and ac lines from the firewall to the compressor. Still need the injectors, pedals with resevoir, injectors, and shift cover.
#15
1JZ Single SC400
Thread Starter
iTrader: (59)
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Received 15 Likes
on
12 Posts
Found some injectors, 880 cc, manifold, down pipe, exhaust with muffler, waste gate, and clutch cylinder. Just looking for a good set of pedals with all the hardware and shift cover in real good shape. Lmk what you have.. Thanks..