AL FS: R154 Complete, Bellhousing, Shifter, Clutch, Flywheel, Pressure Plate
06-30-12, 07:28 PM
#1
1JZ Single SC400
Thread Starter
iTrader: (59)
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Received 15 Likes
on
12 Posts
FS: R154 Complete, Bellhousing, Shifter, Clutch, Flywheel, Pressure Plate
I have finally got my hands on the Soarer R154 with the correct extension. I am selling my current R154 complete. Comes with bellhousing, shifter that has been extended 4", fork, front and rear driveshaft, bolts, center bearing, rear bearing, flywheel, Stage 5 Spec clutch, and pressure plate. The transmission pictured is NOT, I repeat NOT the one you will be getting. I will have to pull mine out in the next week or two. This will allow someone to gather the funds together, if not already. I would rather not part out at this time. If no one buy the whole complete kit, then I will part out separate. I would also be willing to trade for some very nice CHROME TT RIMS, no knockoffs and must have center caps and no flaking!
Again, all the parts are available now, except for the transmission. I need to swap it out. This tranny also has new front and real seals, and has new Redline tranny fluid it ran in it. The clutch has only 4K miles or less on it. Check out the pictures. Everything is complete. The hub was also replaced with the clutch. The clutch will hold over 800 on torque. The only thing you will receive not in the pictures is the shifter....
I AM ASKING 2K FOR THE ENTIRE SETUP, EVERYTHING PICTURED, EXCEPT THIS IS NOT THE TRANNY YOU WILL BE RECEIVING, IT WILL BE THE STANDARD MKIII ONE. MUST GIVE ME A COUPLE OF WEEKS OR LESS TO PULL IT OUT...
ANY QUESTIONS, TEXT ME AT 205-482-5533 OR CALL, OR PM ME! LOOK AT MY TRADER SCORE, I DONT SELL CRAP!!!!
Mark
Again, all the parts are available now, except for the transmission. I need to swap it out. This tranny also has new front and real seals, and has new Redline tranny fluid it ran in it. The clutch has only 4K miles or less on it. Check out the pictures. Everything is complete. The hub was also replaced with the clutch. The clutch will hold over 800 on torque. The only thing you will receive not in the pictures is the shifter....
I AM ASKING 2K FOR THE ENTIRE SETUP, EVERYTHING PICTURED, EXCEPT THIS IS NOT THE TRANNY YOU WILL BE RECEIVING, IT WILL BE THE STANDARD MKIII ONE. MUST GIVE ME A COUPLE OF WEEKS OR LESS TO PULL IT OUT...
ANY QUESTIONS, TEXT ME AT 205-482-5533 OR CALL, OR PM ME! LOOK AT MY TRADER SCORE, I DONT SELL CRAP!!!!
Mark
07-02-12, 10:22 AM
#4
1JZ Single SC400
Thread Starter
iTrader: (59)
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Received 15 Likes
on
12 Posts
I have decided to part some of this. I will sell as follows:
Driveshaft front, with good center bearing $125.00
Driveshaft Rear, with good rear bushing $100
Both combined $200
R154 with bellhousing for 1JZ or 2JZ, clutch fork, and extended shifter $900
Spec Clutch Stage 5 with pressure plate and throwout bearing $400
Stock flywheel and bolts $150
I will not part out just the bellhousing. These prices are not with shipping. Shipping is extra. Paypal is marklinley36@gmail.com, and send as gift. Thanks
Driveshaft front, with good center bearing $125.00
Driveshaft Rear, with good rear bushing $100
Both combined $200
R154 with bellhousing for 1JZ or 2JZ, clutch fork, and extended shifter $900
Spec Clutch Stage 5 with pressure plate and throwout bearing $400
Stock flywheel and bolts $150
I will not part out just the bellhousing. These prices are not with shipping. Shipping is extra. Paypal is marklinley36@gmail.com, and send as gift. Thanks
Last edited by 1JZPWRD; 07-02-12 at 10:26 AM.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
8052JZ
SC400 / 300 Classifieds
7
04-06-15 08:16 AM
TRDmike
SC400 / 300 Classifieds
25
01-29-11 09:25 PM
dumdumgreg
SC400 / 300 Classifieds
14
06-19-10 10:22 PM
