want LS460 brakes?
.
07-31-07, 12:19 PM
#52
Got an email reply...
本題の輸出の件ですが、現段階では考えていません。
この商品はしばらくはファクトリーに来店して頂いたお客さん限定で
販売していく予定です。
一応、キットとして設定していますが、取付するにあたり細かい所を
加工する作業が必要になります。
キャリパー・ローターはもちろん車両側の加工もあります。
加工の難易度は高くないのですが、きちんとした寸法関係の加工が
必要な為、しばらくの間はファクトリー限定商材として取扱う予定です。
将来的にはこのキットの反響や販売要望を考慮した上で
車両側で加工が必要なパーツを含めて、全て加工済みにして出荷する事も
考えています。
ただし、その場合も国内限定になると思います。
商品の性質上、当社でも生産物保険をかけて販売・取付をしていますが
保険の適用範囲が国内のみに限定されています。
もちろん、個人的に国内で購入して海外に持ち出す事は可能だとは思いますが。
Pretty much says
1: At this point, it is only offered to those who bring their car to their shop since some parts (car AND caliper) needs to be fitted for the LS caliper.
2: They are considering to sell this as a kit in the future depending on customer response.
3: However, even if it is released as a kit, it will be only for domestic (Japan) only due to its nature of insurance and brakes. They do sell them with some kind of manufacturers insurance or something but it will not apply outside of Japan.
4: BUT, you could personally buy them in Japan and ship them to the States...
so we pretty much won't be getting KSP Engineering as a vendor. And we won't be able to buy this kit unless it sells well in Japan.
Sorry guys, I tired
本題の輸出の件ですが、現段階では考えていません。
この商品はしばらくはファクトリーに来店して頂いたお客さん限定で
販売していく予定です。
一応、キットとして設定していますが、取付するにあたり細かい所を
加工する作業が必要になります。
キャリパー・ローターはもちろん車両側の加工もあります。
加工の難易度は高くないのですが、きちんとした寸法関係の加工が
必要な為、しばらくの間はファクトリー限定商材として取扱う予定です。
将来的にはこのキットの反響や販売要望を考慮した上で
車両側で加工が必要なパーツを含めて、全て加工済みにして出荷する事も
考えています。
ただし、その場合も国内限定になると思います。
商品の性質上、当社でも生産物保険をかけて販売・取付をしていますが
保険の適用範囲が国内のみに限定されています。
もちろん、個人的に国内で購入して海外に持ち出す事は可能だとは思いますが。
Pretty much says
1: At this point, it is only offered to those who bring their car to their shop since some parts (car AND caliper) needs to be fitted for the LS caliper.
2: They are considering to sell this as a kit in the future depending on customer response.
3: However, even if it is released as a kit, it will be only for domestic (Japan) only due to its nature of insurance and brakes. They do sell them with some kind of manufacturers insurance or something but it will not apply outside of Japan.
4: BUT, you could personally buy them in Japan and ship them to the States...
so we pretty much won't be getting KSP Engineering as a vendor. And we won't be able to buy this kit unless it sells well in Japan.
Sorry guys, I tired
08-01-07, 04:19 AM
#55
couldnt someone with any decnet bit of fabrication experience just fab up a template for the brackets we need so we can autocad the hell out of it and have htem made?
rotors are a whole different, but not as complicated matter (prolly adapt some brembo/rotora/stoptech that are the right size (or similar) and fit 5x4.5PCD
rotors are a whole different, but not as complicated matter (prolly adapt some brembo/rotora/stoptech that are the right size (or similar) and fit 5x4.5PCD
08-04-07, 11:56 PM
#57
couldnt someone with any decnet bit of fabrication experience just fab up a template for the brackets we need so we can autocad the hell out of it and have htem made?
rotors are a whole different, but not as complicated matter (prolly adapt some brembo/rotora/stoptech that are the right size (or similar) and fit 5x4.5PCD
rotors are a whole different, but not as complicated matter (prolly adapt some brembo/rotora/stoptech that are the right size (or similar) and fit 5x4.5PCD
On a more serious note, I'm sure its not too hard either, but then again I haven't worked on the new LS brakes so I'm just speculating.
