We all know these damn cars lean on the driver side, how does this sound for a fix...
#62
Lexus Champion
Thread Starter
Body panels are straight, the suspension is off. That is why it leans. I don't know how many other way I need to explain it. The frame is close to the ground on the driver side, The A arm pivot where it bolts to the frame is closer to the ground on the driver side, The passenger side rides firmer up front.
You don't need to be **** Tracey to realize the reason for the lean isn't the body panels.
You don't need to be **** Tracey to realize the reason for the lean isn't the body panels.
#63
But realistically, that's going overboard with a street car, unless of course you are a track nut.
#64
I would hope so...
This is a unibody car, there is no frame....
It's not as simple as the fenders and quarter panels being off a bit, it's the entire structure beneath the outside sheet metal married to the tub (floor of the car) that may be slightly off
Are you sure your measuring on a level plane?
Paul Tracy is a paid driver, not an engineer and would probably say the same thing you are "the car's leaning"... "fix it".
The only way you are going to be able to fix it, is to put the coilovers back on or have quarter inch spacers machined to the same dimensions as the upper strut mounts on the drivers side, punch out the studs in the oe strut mounts and use longer bolts that allow you to sandwich the spacers between the shocktower and the strutmount.
or quit *****in and live with it, I'm not trying to be an a-hole, but you had a solution before and now are back to the oe suspension and there is no simple fix....sorry.
This is a unibody car, there is no frame....
It's not as simple as the fenders and quarter panels being off a bit, it's the entire structure beneath the outside sheet metal married to the tub (floor of the car) that may be slightly off
The only way you are going to be able to fix it, is to put the coilovers back on or have quarter inch spacers machined to the same dimensions as the upper strut mounts on the drivers side, punch out the studs in the oe strut mounts and use longer bolts that allow you to sandwich the spacers between the shocktower and the strutmount.
or quit *****in and live with it, I'm not trying to be an a-hole, but you had a solution before and now are back to the oe suspension and there is no simple fix....sorry.
#65
Tech Info Resource
iTrader: (2)
And he still refuses to move the shock from one side to the other to see if the issue moves with the shock. That would answer the question about the shock losing its gas charge and end any discussion about the problem being the spring or shock.
#66
Lexus Fanatic
iTrader: (33)
sincityIS is not the only member in the 2IS community here that has agreed to this being a problem....
Why is it that other members in this thread have said they had to compensate on the drive side with coilovers for the car to be level? Giggity you are telling sincityIS to put his Coils back on "or" use spacers. I would and do have an issue that I have a 48k car and the car is not level. I had to make some major mods to my car on the rear driver side to compensate for the rims and tires?? Why did I not have to do it on the passenger side if the car sits so dam level??
Regardless how you look at this there is a QC issue with the 2IS. When its time to get rid of my car and the OEM springs go back on I will bring this back to life to see how my car sits.
Another thing is how does anyone know that the springs are sitting in the same spot on sincityIS's car?? they are not side specific and I know my springs are generically sitting in the box. So when they are installed back onto my car only GOD will know if they are in the same spot as they previously where!
Why is it that other members in this thread have said they had to compensate on the drive side with coilovers for the car to be level? Giggity you are telling sincityIS to put his Coils back on "or" use spacers. I would and do have an issue that I have a 48k car and the car is not level. I had to make some major mods to my car on the rear driver side to compensate for the rims and tires?? Why did I not have to do it on the passenger side if the car sits so dam level??
Regardless how you look at this there is a QC issue with the 2IS. When its time to get rid of my car and the OEM springs go back on I will bring this back to life to see how my car sits.
Another thing is how does anyone know that the springs are sitting in the same spot on sincityIS's car?? they are not side specific and I know my springs are generically sitting in the box. So when they are installed back onto my car only GOD will know if they are in the same spot as they previously where!
#68
Tech Info Resource
iTrader: (2)
Or if they were installed correctly or if there really is a QC issue. None of these questions have been answered.
#69
Tech Info Resource
iTrader: (2)
I deleted two unnecessary comments destructive to our sense of community. While I still have my own position about the issue recorded here, it is completely unnecessary to jab at anyone for any reason. Discussion and debate are healthy. Personal jabs are not and won't be tolerated.
Continue...
Continue...
#70
Lexus Champion
Thread Starter
It is because the car is heavier on the driver side. I have no clue how to compensate other than adding preload to the driver side, but that is impossible to do without coilovers.
#71
Lexus Champion
iTrader: (2)
So, to recap this thread to this point...............................
1.) The IS is a unibody car, so no individual fenders are out of alignment, the
whole car structure leans.
2.) Shocks are side specific, they can't be switched to see if that is the
cause of our leaning.
3.) OEM and aftermarket springs do not alleviate the lean in our cars.
4.) Coilovers, or adding washers to OEM suspension are possibly the best
solutions to solve this dilemma.
.....................am I leaving anything out?
1.) The IS is a unibody car, so no individual fenders are out of alignment, the
whole car structure leans.
2.) Shocks are side specific, they can't be switched to see if that is the
cause of our leaning.
3.) OEM and aftermarket springs do not alleviate the lean in our cars.
4.) Coilovers, or adding washers to OEM suspension are possibly the best
solutions to solve this dilemma.
.....................am I leaving anything out?
#73
Tech Info Resource
iTrader: (2)
NOt that I refuse to switch the shocks, but the shocks are SIDE SPECIFIC. Its the springs that are not side specific. I could switch the sides, but you ened to disassemble the shocks to switch the coils. I am fairly certain this won't make a difference though since I have had OEM coils and Eibachs on this car and they both resulted in a lean.
It is because the car is heavier on the driver side. I have no clue how to compensate other than adding preload to the driver side, but that is impossible to do without coilovers.
It is because the car is heavier on the driver side. I have no clue how to compensate other than adding preload to the driver side, but that is impossible to do without coilovers.
Another thought - did you disconnect the sway bar to see if it leveled out with one end disconnected?
And again, did you reset the bushings according to the service manual when you put the suspension together? If the bushings are not neutral at normal ride height they will impact overall ride height.
There is still no solid evidence the car is not balanced L/R except you think it must be. If you corner weighed the car, you'd know for sure, it would be obvious from the numbers.
#74
Rookie
iTrader: (15)
For what it's worth, my 2nd gen GS does the same thing when it was stock, and even when it's lowered on l-tuned springs. The driver side has less finger gap than the passenger. I've learned to accept it as there is nothing I can really do in short of modifying the suspension or getting coilovers.
As for corner balancing, you can usually find them at a more dedicated alignment shop. Most average joe shops will not have the balancer. Time to look up the yellow pages if you're serious about it. The price isn't entirely cheap though. Expect to pay ~$250 for corner balancing/alignment depending on your location.
Those of you who have coilovers and want to get the most out of your setup for handling purposes, get your car corner balanced. Being able to adjust the height is just a perk. Having the ability to corner balance your vehicle is where the money and gold is at. Then again, most people on here will use their coilovers for aesthetic reasons
As for corner balancing, you can usually find them at a more dedicated alignment shop. Most average joe shops will not have the balancer. Time to look up the yellow pages if you're serious about it. The price isn't entirely cheap though. Expect to pay ~$250 for corner balancing/alignment depending on your location.
Those of you who have coilovers and want to get the most out of your setup for handling purposes, get your car corner balanced. Being able to adjust the height is just a perk. Having the ability to corner balance your vehicle is where the money and gold is at. Then again, most people on here will use their coilovers for aesthetic reasons
#75
Lexus Fanatic
iTrader: (33)
Lets say the Tech did not do this?? Can I do this in my garage if I have the appropriate tools or does the car need to be at an alignment shop for this to be done correctly?
I am curious to check this out.
Thanks!