what's your entire brake set up?
#1
Lexus Champion
Thread Starter
what's your entire brake set up?
don't know if there's a thread like this, i haven't seen it in the first 2 pages so it's probably dead. what does everyone use to stop? i'm gonna be doing a few tweaks to my system and was just wondering.
currently i have TT calipers all around, will be getting drilled rotors since mine are warped and the rear ones are the wrong size (too small) also will be getting some Techna Fit SS lines. also what do you guys think of ebay rotors? i found some drilled ones all four for TT supra for 225 bucks. that's the cheapest i've found anywhere.
currently i have TT calipers all around, will be getting drilled rotors since mine are warped and the rear ones are the wrong size (too small) also will be getting some Techna Fit SS lines. also what do you guys think of ebay rotors? i found some drilled ones all four for TT supra for 225 bucks. that's the cheapest i've found anywhere.
#3
Lexus Champion
Thread Starter
what about SS lines? are they worth it? my lines seem to be ok for now, but i thought since i'll be replacing the rotors, might as well do the lines right? idk just a thought
#4
Skip the drilled or slotted rotors unless they are DBA or another multi-piece rotor. Reason being is they aren't up for the punishment (mostly for looks) and tend to crack from heat cycling on the street and even more-so on the track. Stick with high carbon content blank rotors and some good pads and you'll be more than set for 99% of people. Everyone wants to shed heat, but in reality you want a decent amount of heat in the rotors and pads to make them effective (best friend is a brake engineer for honda motorsports and did the new NSX's brakes) Braided lines aren't a bad idea since stock lines are around 20 years old now. Just make sure you buy high quality that are DOT or TUV approved and you'll be set.
#5
Instructor
iTrader: (5)
Skip the drilled or slotted rotors unless they are DBA or another multi-piece rotor. Reason being is they aren't up for the punishment (mostly for looks) and tend to crack from heat cycling on the street and even more-so on the track. Stick with high carbon content blank rotors and some good pads and you'll be more than set for 99% of people. Everyone wants to shed heat, but in reality you want a decent amount of heat in the rotors and pads to make them effective (best friend is a brake engineer for honda motorsports and did the new NSX's brakes) Braided lines aren't a bad idea since stock lines are around 20 years old now. Just make sure you buy high quality that are DOT or TUV approved and you'll be set.
Couldn't say it any better.
Supra TT all around with Centric blanks here. Fairly aggressive EBC yellows all around. Yes they like a bit of heat before they start working.
#6
Thanks, I appreciate it. I'm all about giving correct information in the world where people base everything off of what some random non-professional says, instead I do the math and actually try it out first; I'm all about proper engineering with numbers to back it when it comes to cars.
I dig your setup and have the same, except for pads, as you on my current project SC. I don't think people know that Centric is the manufacturer for StopTech and their stock blanks are great track killers.
INTIMAZY have you replaced your stock hard-lines yet? If not, I suggest it...you wouldn't believe the obstructions/buildup I found in the lines on a correctly serviced 1 owner.
I dig your setup and have the same, except for pads, as you on my current project SC. I don't think people know that Centric is the manufacturer for StopTech and their stock blanks are great track killers.
INTIMAZY have you replaced your stock hard-lines yet? If not, I suggest it...you wouldn't believe the obstructions/buildup I found in the lines on a correctly serviced 1 owner.
Trending Topics
#11
Lexus Champion
Thread Starter
can you explain why drilled rotors are less beneficial than solids? i understand slotted rotors eat your brake pads so i'm staying away from those, but i thought drilled rotors were fine? i'm new to this so i'm just willing to learn.
#12
Instructor
iTrader: (5)
The discussion changes if you talk about 2-piece rotors but 1-piece OEM style rotors that are drilled or slotted crack under heavy use. They're best reserved for street-posing.
#13
Pole Position
Join Date: Dec 2007
Location: california
Posts: 309
Likes: 0
Received 0 Likes
on
0 Posts
I had slotted and drilled rotors on my IS for the longest time for street use and no real spirited driving. Never had any problems with them. However, when it came time to change my pads, the rotors had developed an outer lip so they needed resurfacing. I couldn't find a shop to resurface them. They said it was because the drilled and slotted surfaces would mess up their bit or whatever. But like INTIMAZY stated, they're great for street posing.
#15
Haha I had to laugh at this, my friend is building a GTO ground up and did this exact same thing when flaring his hard lines