EDFC Install Project: GS400
#33
Thread Starter
Northern California Regional Officer
iTrader: (5)
Joined: May 2001
Posts: 8,702
Likes: 5
From: California
Originally Posted by engin_ear
Oldie but a goodie.
This was awesome work.
This gets my vote as the best ever mod in a GS interior.
This was awesome work.
This gets my vote as the best ever mod in a GS interior.
Wow, thanks !!!
It's been 3 years since this was done and I can say that everything is holding up well and I haven't touched the install since.
Those in NorCal who want to see this in person, just come to the EOS meet and I'll be happy to show it to ya. Shamless plug. www.LGWNorCal.com
Interestingly enough I am doing another EDFC custom install that I think would be a good alternative location to this one. I will post that idea in say a month or so.
#35
Originally Posted by RMMGS4
Interestingly enough I am doing another EDFC custom install that I think would be a good alternative location to this one. I will post that idea in say a month or so.
#36
Originally Posted by RMMGS4
Wow, thanks !!!
It's been 3 years since this was done and I can say that everything is holding up well and I haven't touched the install since.
Those in NorCal who want to see this in person, just come to the EOS meet and I'll be happy to show it to ya. Shamless plug. www.LGWNorCal.com
Interestingly enough I am doing another EDFC custom install that I think would be a good alternative location to this one. I will post that idea in say a month or so.
It's been 3 years since this was done and I can say that everything is holding up well and I haven't touched the install since.
Those in NorCal who want to see this in person, just come to the EOS meet and I'll be happy to show it to ya. Shamless plug. www.LGWNorCal.com
Interestingly enough I am doing another EDFC custom install that I think would be a good alternative location to this one. I will post that idea in say a month or so.
1) Have you had any EDFC problems at all? Motors? Need to reset the thing ever?
2) Where's the other location? No need for proprietary details, I'm just getting ready to put mine in.
Jerry
#37
Thread Starter
Northern California Regional Officer
iTrader: (5)
Joined: May 2001
Posts: 8,702
Likes: 5
From: California
Originally Posted by engin_ear
I have 2 questions then Glen:
1) Have you had any EDFC problems at all? Motors? Need to reset the thing ever?
2) Where's the other location? No need for proprietary details, I'm just getting ready to put mine in.
Jerry
1) Have you had any EDFC problems at all? Motors? Need to reset the thing ever?
2) Where's the other location? No need for proprietary details, I'm just getting ready to put mine in.
Jerry
Nope, never touched a thing since it went in. Motors get excercised often and no issues. All my wires were soldered and tie-wrapped neatly, so that doesn't hurt.
The other location is replacing the ashtray door with a glass molded piece and using a bolt on design, allowing everything to go back to stock.
#38
Originally Posted by RMMGS4
Nope, never touched a thing since it went in. Motors get excercised often and no issues. All my wires were soldered and tie-wrapped neatly, so that doesn't hurt.
The other location is replacing the ashtray door with a glass molded piece and using a bolt on design, allowing everything to go back to stock.
The other location is replacing the ashtray door with a glass molded piece and using a bolt on design, allowing everything to go back to stock.
In fact, just tonight I ripped the EQ & Sirius out, and putting in a digital EQ controller & bass maximizer EPIC-160 in its place. I think I'm putting the EDFC under the steering wheel where the air vent is. Just a bit hard to access there.
Thread
Thread Starter
Forum
Replies
Last Post